Denon DVD-3800BDCI User Manual

6

Keep in mind the following when using the remote control:
• Make sure that there are no obstacles between the remote 

control and infrared sensor window on the unit.

• Remote operation may become unreliable if strong sunlight or 

fluorescent light is shining on infrared sensor window of the 
unit.

• Remote control for different devices can interfere with each 

other. Avoid using remote control for other equipment located 
close to the unit.

• Replace the batteries when you notice a fall off in the operating 

range of the remote control.

• The maximum operable ranges from the unit are as follows.

If you have other DENON’s DVD players around this unit, this unit 
reacts to the commands you made for DVD players through its 
remote control. To avoid this situation, you can set this unit not 
react to other DENON’s DVD player's remote control.

• “Only Attached Remocon” will be displayed on the upper 

right corner of the screen and this unit only react to the 
commands from this unit's remote control.

• To set back to default, press [7],[8],[9],[1] at step 2. “Normal 

Remocon” will be displayed on the upper right corner of the 
screen and this unit react to both the commands from this unit's 
remote control and the other DENON’s DVD players' remote 
control.

To avoid the other DENON’s BD players responding the remote 
signal of this unit, you can change the signal code of the remote 
control. If the signal code of the remote control does not match to 
the signal code of the unit, you cannot control the unit with the 
remote control.

䡵 Change the signal code of the unit 

2) Use [Y / Z] to select 

3) Use [Y / Z] to select 

4) Use [U / V] to select “Remote Control Setting”.
5) Press [ENTER] to select “DENON1” or “DENON2”.

6) Press [SETUP] to exit.
• At this point the new signal code of the unit is effective. Please 

change the signal code of the remote control to match to the 
signal code of the unit with following procedure.

䡵 Change the signal code of the remote control

Set to “DENON1”: 
Press and hold [RETURN], and press [3], [2], [1].
Set to “DENON2”: 
Press and hold [RETURN], and press [1], [2], [3].

• If the signal code does not match, the signal code of the remote 

control will be displayed on the front panel display. 

• The default setting and the setting after you change the 

batteries is “DENON1”.

A Open the battery 

compartment cover.

B Insert two “AA” (R6P) 

batteries, with each one 
oriented correctly.

C Close the cover.

• Use “AA” (R6P) batteries in this remote control.
• Replace the batteries with new ones approximately once a 

year, though this depends on the frequency with which the 
remote control is used.

• If the remote control does not operate within a close 

proximity of the main unit, replace the batteries with new 
ones, even if less than a year has passed.

• The included batteries serve only for verifying operation. 

Replace them with new batteries as soon as possible.

• When inserting the batteries, be careful to do so in the 

proper direction, following the   and   marks in the remote 
control’s battery compartment.

• To prevent damage or battery fluid leakage:

- Do not mix a new battery with an old one.
- Do not mix two different types of batteries such as alkaline 

and manganese.

- Do not short-circuit, disassemble, heat or dispose of 

batteries in flames.

• Remove the batteries when not planning to use the remote 

control for a long period of time.

• If the batteries should leak, carefully wipe off the fluid from 

the inside of the battery compartment, then insert new 
batteries.

approx. 23 feet (7m)

- Either side of the center: approx. 23 feet (7m) within 30°

• The setting remains after you turn off this unit or unplug the 

AC cord.

• If you try to operate this unit with the other DENON’s DVD 

players' remote control, some of the operation may not 
available depends on the manufactured year or type of the 
remote control.

OFF

ON

ON / STANDBY

HDMI

RESOLUTION

VIDEO NOISE
REDUCTION

BLU-RAY DISC PLAYER 

DVD-3800BDCI

30°

30°

23 feet (7m) 30°

23 feet (7m)

23 feet (7m) 30°

Power Saving

 

Off

Remote Control Setting

  DENON1

Media Select 

 Disc

E5E00UD_EN.book  Page 6  Friday, January 18, 2008  6:59 PM