Powermatic 719T User Manual

Page of 24
 
 
 
Operating Instructions and Parts Manual 
Tilting Table Hollow Chisel Mortiser 
Model: 719T 
 
 
 
 
Powermatic 
 
427 New Sanford Road 
 
LaVergne, Tennessee 37086 
Part No. M-2474002 
Ph.: 800-274-6848 
Revision B2  02/2014 
www.powermatic.com 
Copyright © 2014 Powermatic 
This .pdf document is bookmarked

Summary of Contents of user manual for Powermatic 719T

  • Page 1: 719T Hollow Chisel Mortiser

    This .pdf document is bookmarked Operating Instructions and Parts Manual Tilting Table Hollow Chisel Mortiser Model: 719T Powermatic 427...

  • Page 2: Warranty and Service

    Warranty and Service Powermatic warrants every product it sells against manufacturers’ defects. If one of our tools needs service or...

  • Page 3: Table of Contents

    Table of Contents Warranty and Service .............................................................................................................................. 2  Table of Contents .................................................................................................................................... 3  Warnings ................................................................................................................................................. 4  Introduction ............................................................................................................................................. 6  Specifications...

  • Page 4: Warnings

    Warnings 1. Read and understand the entire owner’s manual before attempting assembly or operation. 2. Read and understand the warnings...

  • Page 5

    21. Make your workshop child proof with padlocks, master switches or by removing starter keys. 22. Give your work undivided...

  • Page 6: Specifications

    Introduction This manual is provided by Powermatic covering the safe operation and maintenance procedures for a Powermatic Model 719T Tilting...

  • Page 7: Unpacking

    Unpacking Remove mortiser and stand from the shipping cartons. Report any damage immediately to your distributor and shipping agent. Do...

  • Page 8: Electrical Connections

    Electrical Connections A separate electrical circuit should be used for your machines. This circuit should not be less than #12...

  • Page 9

    3. Grounded, cord- connected tools intended for use on a supply circuit having a nominal rating between 150 - 250...

  • Page 10: Assembly

    Assembly Do not connect the machine to power source until completely assembled. Read and understand the entire manual. Securing Machine...

  • Page 11

    Installing Chisel and Bit Referring to Figure8: 1. Loosen the lock screw. 2. Insert the chisel bushing into the head...

  • Page 12: Operating Controls

    Operating Controls Start/Stop Switch Referring to Figure 10: The Start/Stop Switch is located to the left of the motor on...

  • Page 13: Adjustments

    Adjustments 90° Chisel to Worktable Calibration Referring to Figure 12: Place a square (E) so it rests against the worktable...

  • Page 14

    6. Reinstall the chisel bushing (F) and secure it loosely with the lock screw (E). 7. Reinstall the chisel and...

  • Page 15: Operation

    Chisel Parallel to Workpiece Referring to Figure 16: The chisel can be adjusted parallel to the workpiece as follows: 1....

  • Page 16: Maintenance

    Do not have the chisel slot against the blind end of the mortise, as the chips will not be...

  • Page 17: Replacement Parts

    Chisel Sharpen the chisel with a mortise chisel cutter with the correct size pilot. (Pilot size will differ depending on...

  • Page 18

    719T Mortiser Assembly 18

  • Page 19

    719T Mortiser Parts List Index No. Part No. Description Size Qty ................. 2474002T ................719T Mortiser Assy (Index No. 1 thru...

  • Page 20

    Index No. Part No. Description Size Qty 56 ............. 719T-156 .................Hydraulic Cylinder ................................................................................. 1 57 ............. 6294180...................C-Clip .................................................................................................... 2 58...

  • Page 21

    Index No. Part No. Description Size Qty 113 ........... TS-1540061 .............Hex Nut ..............................................................M8 .............................. 2 114 ........... TS-1491021 .............Hex Cap...

  • Page 22

    719T Mortiser Stand Parts List Index No. Part No. Description Size Qty ................. 6294235T ................Stand Assembly (Items 1 thru 8)...

  • Page 23

    Optional Accessories Index No. Part No. Description ................. 1791096...................Set of 4 Mortise Chisels and Bits (1/4”, 5/16”, 3/8” and 1/2”)........................

  • Page 24: Dimensions for 719T with premium chisels mounted

    Dimensions for 719T with premium chisels mounted (Chisels and bits purchased separately) Powermatic 719T Mortiser and Chisel Dimensions 1791091 1791092...

downloadlike
ArtboardArtboardArtboard
Report Bug