Panasonic DMR-EH50 User Manual
57
RQT8023
Co
n
ven
ie
nt
fu
n
cti
o
n
s
Channel/Clock settings when TV Guide On Screen
TM
system is not used
Refer to the control reference on page 54.
Preparation:
If the television program list has already been downloaded, return the unit to the factory preset condition using the steps indicated below.
If the television program list has already been downloaded, return the unit to the factory preset condition using the steps indicated below.
When the unit is on and stopped
1
Press and hold [
X
CH] and [
W
CH] on the main unit for about five
seconds.
The unit turns off.
The unit turns off.
2
Press [
Í
DVD POWER] to turn the unit on.
3
Complete the TV Guide On Screen
TM
system setup (until [ENTER]
is pressed after the “Watch TV” message screen is displayed).
[Note]
You can set scheduled recording only manually after you set the unit with “Set Channels Automatically”.
1
Press [SETUP].
2
Press [
3
,
4
] to select “Channel” and
press [
1
].
3
Press [
3
,
4
] to select “Set Channels
Automatically” and press [ENTER].
4
Press [
2
,
1
] to select “Yes” and
press [ENTER].
5
Press [ENTER].
Auto Channel Setting starts. This takes a few minutes.
The unit then proceeds with Auto Clock Setting. The time is
displayed when finished.
The unit then proceeds with Auto Clock Setting. The time is
displayed when finished.
≥
DST, Daylight Saving Time, shows the summertime setting.
≥
TIME ZONE shows the time difference from Greenwich
Mean Time (GMT).
Mean Time (GMT).
EST (Eastern Standard Time)
l
GMT
j
5
CST (Central Standard Time)
l
GMT
j
6
MST (Mountain Standard Time)
l
GMT
j
7
PST (Pacific Standard Time)
l
GMT
j
8
AST (Alaska Standard Time)
l
GMT
j
9
HST (Hawaii Standard Time)
l
GMT
j
10
For other areas: xx hr
≥
If the Auto Clock Setting does not start automatically, select
“Clock Settings” from the “Setup” tab and then select “Set
Clock Automatically”.
“Clock Settings” from the “Setup” tab and then select “Set
Clock Automatically”.
≥
If the time was not set correctly, use manual clock setting
(
(
➡
17) or adjust time zone.
6
Press [ENTER].
≥
The unit configures channels according to the Signal Source
(RF IN) settings as follows.
Adjust the time zone (
j
1 or
i
1) if it was not set correctly with auto
clock setting.
You cannot change this setting if you set the clock manually.
You cannot change this setting if you set the clock manually.
1
Press [SETUP].
2
Press [
3
,
4
] to select “Setup” and
press [
1
].
3
Press [
3
,
4
] to select “Clock
Settings” and press [ENTER].
4
Press [
3
,
4
] to select “Adjust Time
Zone” and press [ENTER].
5
Press [
3
,
4
] to select “
s
1” or “
r
1”
and press [ENTER].
To return to the previous screen
Press [RETURN].
Press [RETURN].
To exit the screen
Press [SETUP].
Press [SETUP].
To cancel partway while Auto Channel/Clock Setting is taking place
Press [RETURN].
Press [RETURN].
I N 2
I N 2
C H
C H
HDD DVD SD
S VIDEO
S VIDEO
VIDEO
VIDEO
L/MONO
L/MONO-AUDIO
AUDIO-R
OPEN/CLOSE
OPEN/CLOSE
DRI
DRIVE
VE
SELECT
SELECT
REC
REC
/x1.3
X
CH
W
Auto channel/clock settings
Channel
SETUP
Setup
Disc
Video
Audio
Audio
Set Clock Automatically
Auto Clock Setting is complete.
4/4/2005 12:15 AM
DST.............. On
Time Zone..... CST
Signal Source
(RF IN)
Band
Channel
Antenna
VHF
2–13
UHF
14–69
CableTV
VHF
2–13
CATV LOW BAND
95–99
CATV MID/SUPER BAND
14–36
CATV HYPER BAND
37–65
ULTRA BAND
66–94
100–125
SPECIAL CATV CHANNEL
1
Adjust Time Zone
SETUP
Setup
Disc
Video
Adjust Time Zone
j
1
0
i
1
Channel
EH50English.book Page 57 Tuesday, February 1, 2005 6:36 PM