Pioneer PDP-5071 User Guide
67
En
Adjustments and Settings
11
En
gl
is
h
Power Control
Power Control provides convenient functions for saving power.
Energy Save
You may use one of the three Energy Save modes to save power
consumption.
consumption.
1
Press
HOME MENU.
2
Select “Power Control”. ( / then
ENTER)
3
Select “Energy Save”. ( / then
ENTER)
4
Select “Save1”, “Save2”, or “Picture Off”. ( / then
ENTER)
ENTER)
5
Press
HOME MENU to exit the menu.
NOTE
• You can also select this function using the Home menu
when the input source is a PC.
No Signal off (AV mode only)
The system will be automatically placed into the standby mode
if no signal is received for 15 minutes.
if no signal is received for 15 minutes.
1
Press
HOME MENU.
2
Select “Power Control”. ( / then
ENTER)
3
Select “No Signal off”. ( / then
ENTER)
4
Select “Enable”. ( / then
ENTER)
5
Press
HOME MENU to exit the menu.
NOTE
• Five minutes before the system is placed into the standby
mode, a message appears every minute.
• The system may not be placed into the standby mode when
noise signals are present at the Plasma Display System after
a TV program finishes.
a TV program finishes.
No Operation off (AV mode only)
The system will be automatically placed into the standby mode
when no operation is performed for three hours.
when no operation is performed for three hours.
1
Press
HOME MENU.
2
Select “Power Control”. ( / then
ENTER)
3
Select “No Operation off”. ( / then
ENTER)
4
Select “Enable”. ( / then
ENTER)
5
Press
HOME MENU to exit the menu.
NOTE
• Five minutes before the system is placed into the standby
mode, a message appears every minute.
Power Management (PC mode only)
The system will be automatically placed into the standby mode
when no signal is received from the personal computer.
when no signal is received from the personal computer.
1
Press
HOME MENU.
2
Select “Power Control”. ( / then
ENTER)
3
Select “Power Management”. ( / then
ENTER)
4
Select “Mode1” or “Mode2”. ( / then
ENTER)
5
Press
HOME MENU to exit the menu.
Item
Description
Standard
Maximum picture brightness; may increase glass
panel buzzing.
panel buzzing.
Save1
Slightly reduced power consumption and brightness;
optimal setting for most uses.
optimal setting for most uses.
Save2
Lowest power consumption; slightly decreased
brightness.
brightness.
Picture Off
Deactivates the screen to save power. To restore the
screen display, press any button other than
screen display, press any button other than
VOL +/–
and
MUTING.
This setting is not memorized by the system.
Item
Description
Disable
(factory default)
(factory default)
Does not place the system into the standby mode.
Enable
Places the system into the standby mode if no signal
is received for 15 minutes.
is received for 15 minutes.
Item
Description
Disable
(factory default)
(factory default)
Does not place the system into the standby mode.
Enable
Places the system into the standby mode if no
operation is performed for three hours.
operation is performed for three hours.
Item
Description
Off
(factory default)
(factory default)
No power management
Mode1
• Places the system into the standby mode when no
signal is received from the personal computer for
eight minutes.
eight minutes.
• Even when you start using the computer and a
signal is received again, the system stays off.
• The system is switched on again by pressing
STANDBY/ON on the Plasma Display or TV on
the remote control unit.
the remote control unit.
Mode2
• Places the system into the standby mode when no
signal is received for eight seconds.
• When you start using the computer and a signal is
received again, the system is switched on.
• The system is switched on again by pressing
STANDBY/ON on the Plasma Display or TV on
the remote control unit.
the remote control unit.
PDP6070HD.book Page 67 Friday, May 19, 2006 5:01 PM