Runco CX-40HD User Manual
Runco CX-40HD/CX-46HD Owner’s Operating Manual
41
PRE
L
IMINAR
Y
Overscan (not available for RGB input): Overscan pushes the outside edge of the
active picture area of the video signal out beyond the edge of the display area.
active picture area of the video signal out beyond the edge of the display area.
Some television programs are produced based on the assumption that older television
sets may not display the outer edges of the broadcast picture area. Overscan effectively
trims away these inactive, outer edges and enlarges the remaining portion of the image to
fill the display area.
sets may not display the outer edges of the broadcast picture area. Overscan effectively
trims away these inactive, outer edges and enlarges the remaining portion of the image to
fill the display area.
Use the on-screen slidebars to set the desired amount of horizontal and vertical overscan,
as well as horizontal and vertical image shift.
as well as horizontal and vertical image shift.
These settings only affect 480i source material. For HDTV, DVDs and other video sources,
Overscan is generally not necessary or desirable.
Overscan is generally not necessary or desirable.
Input Label: You can give each Crystal Series LCD Display input a descriptive name. To
do this, select Input Label from the Setup menu and choose one from the list.
do this, select Input Label from the Setup menu and choose one from the list.
HDMI Audio: If the HDMI source is a PC or other device that does not support audio
output via HDMI, set HDMI Audio to PC.
output via HDMI, set HDMI Audio to PC.
If the source does support audio output via HDMI, set this option to HDMI to route the
HDMI (digital) audio signal to the speakers when HDMI1 or HDMI2 is selected.
HDMI (digital) audio signal to the speakers when HDMI1 or HDMI2 is selected.
RGB Signal: The RGB input supports both DTV and VESA (computer) resolutions and
signal timings. If the RGB source is a computer, select PC. If it is a DTV set-top box or
other equipment with an RGB output, select Video.
signal timings. If the RGB source is a computer, select PC. If it is a DTV set-top box or
other equipment with an RGB output, select Video.
Film Mode: To smooth out moving images from interlaced, standard-definition (SD)
sources, select Film Mode and set it to Automatic.
sources, select Film Mode and set it to Automatic.
In most cases, the Crystal Series LCD Display detects the proper “pull-down” rate and
vertical frequency. However, if your source is jittery and/or tearing you may wish to specify
the pull-down rate (2:2 or 3:2) to ensure stable processing for that source.
vertical frequency. However, if your source is jittery and/or tearing you may wish to specify
the pull-down rate (2:2 or 3:2) to ensure stable processing for that source.
Auto Backlight: Select Auto Backlight from the Setup menu and set it to On to have the
Crystal Series LCD Display adjust the Backlight setting automatically, according to the
ambient light level in the viewing area.
Crystal Series LCD Display adjust the Backlight setting automatically, according to the
ambient light level in the viewing area.
OSD Timer: Use the
or
button to set the OSD Timer. This timer controls how long
the menus remain on-screen after selecting them. Select from 0 to 60 seconds, in
10-second increments. When you set the OSD to 0, the menus remain on-screen until
you hide them by pressing EXIT.
10-second increments. When you set the OSD to 0, the menus remain on-screen until
you hide them by pressing EXIT.
Auto Off: Set Auto Off to 30, 60 or 120 minutes to have the Crystal Series LCD Display
go into standby mode when no source signal is present for the selected amount of time.
go into standby mode when no source signal is present for the selected amount of time.
When Auto Off is set to zero (0) minutes (disabled), the Crystal Series LCD Display
remains in normal operating mode, regardless of the presence or absence of an input
sync signal.
remains in normal operating mode, regardless of the presence or absence of an input
sync signal.