Panasonic KX-TGA523 User Manual
[OFF]
[+, -, TUNE/CLOCK]
[TIME SET]
1-H Setting Time
1
Press [TIME SET].
2
Adjust the time by pressing
[+, TUNE/CLOCK] or [–, TUNE/CLOCK].
• Pressing [+] or [–] increases or
[+, TUNE/CLOCK] or [–, TUNE/CLOCK].
• Pressing [+] or [–] increases or
decreases the time in one-minute units.
• Pressing and holding [+] or [–]
increases or decreases the time faster.
3
Press [TIME SET] to set the clock.
• The time stops flashing.
• The time stops flashing.
•You can exit time setting mode any time by pressing [OFF].
•If a power failure occurs, the display will show “ ” for about 10
minutes, then it will become blank. After power returns, “
” will
be displayed. The clock memory will be lost. Set the clock. The radio
alarm and buzzer alarm memory will be retained for about 10
minutes during a power failure (4-A, 4-B).
alarm and buzzer alarm memory will be retained for about 10
minutes during a power failure (4-A, 4-B).
Only one handset can be registered at a time.
Make sure the base unit and the other handsets are not being used.
Have both the handset and base unit nearby during registration.
Make sure the base unit and the other handsets are not being used.
Have both the handset and base unit nearby during registration.
The handset display shows the
instructions as shown on the right.
instructions as shown on the right.
1
Base unit: Press and hold the
*LOCATOR button for 3 seconds.
• The CHARGE indicator flashes. After the CHARGE indicator starts
*LOCATOR button for 3 seconds.
• The CHARGE indicator flashes. After the CHARGE indicator starts
flashing, the rest of the procedure must be completed within 1 minute.
•On the KX-FPG391, “HS REGISTRATION” is displayed.
2
Handset:
#Press the soft key (
#Press the soft key (
).
$Wait until a long beep sounds and the
display shows the new extension number.
•Registration is complete.
•The registered number “[1]” to “[4]” is shown on the top right of
the display.
•You can stop registration by pressing [OFF] on the handset and
pressing the *LOCATOR button on the base unit.
•To cancel the handset’s registration, please see the base unit
Operating Instructions.
•If you try to register this handset to the KX-TG6500 base unit,
“Wrong handset Refer to manual” is displayed. The base
units for this handset are mentioned above.
units for this handset are mentioned above.
OK
For assistance, please call: 1-800-211-PANA(7262)
1-G Handset Registration
Getting Started
Section 1
This handset must be registered to a KX-TG5200/KX-TG5202/
KX-TG5210/KX-TG5212/KX-TG5230/KX-TG5240/KX-FPG391 base
unit.
The handset will be assigned an extension number at registration.
The KX-TGA523 will not work without one of the following Panasonic
cordless phone systems: KX-TG5200/KX-TG5202/KX-TG5210/
KX-TG5212/KX-TG5230/KX-TG5240/KX-FPG391.
KX-TG5210/KX-TG5212/KX-TG5230/KX-TG5240/KX-FPG391 base
unit.
The handset will be assigned an extension number at registration.
The KX-TGA523 will not work without one of the following Panasonic
cordless phone systems: KX-TG5200/KX-TG5202/KX-TG5210/
KX-TG5212/KX-TG5230/KX-TG5240/KX-FPG391.
•Base unit model shown here is KX-TG5240.
*
The location of LOCATOR button varies by base unit model.
KX-TG5200/KX-TG5202: LOCATOR [
KX-TG5200/KX-TG5202: LOCATOR [
], [
], [
], [
] or [
]
KX-TG5210/KX-TG5212: LOCATOR/INTERCOM [
], [
], [
],
[
] or [
]
KX-TG5230/KX-TG5240/KX-FPG391: [LOCATOR/INTERCOM/TRANSFER]
Ex. Extension number 2
SP
PRIVACY
[
2
]
Handset [2]
Registered
1-F Battery Charge
Place the handset on the charger and charge
for 6 hours before initial use.
•The unit beeps once, the CHARGE indicator
for 6 hours before initial use.
•The unit beeps once, the CHARGE indicator
lights and “Charging” is displayed.
•When the battery is fully charged, “Charge
completed
” is displayed if there are no
new calls in the Caller List.