Fostex D-108 User Manual
16
D-108 Quick Operation Guide
44.1kHz
8
7
6
5
4
3
2
1
ABS
42
OL
0
30
24
18
12
9
6
3
∞
44.1kHz
SETUP
FORMAT
SURE?
8
7
6
5
4
3
2
1
42
OL
0
30
24
18
12
9
6
3
∞
44.1kHz
SETUP
8
7
6
5
4
3
2
1
42
OL
0
30
24
18
12
9
6
3
∞
44.1kHz
SETUP
8
7
6
5
4
3
2
1
42
OL
0
30
24
18
12
9
6
3
∞
5. Insert an unformatted SCSI disk into the drive and press the EXECUTE/YES key.
The display asks whether you wish to format the SCSI disk. (“#” represents the SCSI ID number, and “*****”
represents the disk name.) The “?” mark of [SURE?] flashes.
represents the disk name.) The “?” mark of [SURE?] flashes.
6. Press the EXECUTE/YES key again.
The Record mode selection menu appears on the display.
The rest of the procedure is the same as described on page 13. Select the desired Record mode and execute
the format operation. When the format operation is completed, press the EXIT/NO key or the STOP button
to exit SETUP mode. The display automatically shows the Time Base indication for the E-IDE hard disk.
To use the SCSI drive as a current drive, you need to switch the current drive setting as explained in the
following “Selecting a current drive” section.
The rest of the procedure is the same as described on page 13. Select the desired Record mode and execute
the format operation. When the format operation is completed, press the EXIT/NO key or the STOP button
to exit SETUP mode. The display automatically shows the Time Base indication for the E-IDE hard disk.
To use the SCSI drive as a current drive, you need to switch the current drive setting as explained in the
following “Selecting a current drive” section.
<Note>
To eject the SCSI disk after formatting, press the EJECT button on the SCSI drive.
Selecting a current drive
As explained earlier, turning on the power to the D-108 and both E-IDE and SCSI drives causes the E-IDE hard
disk to start up as a current drive. If you wish to use the SCSI drive as a current drive, you need to set the
[Drive Sel.?] (Selecting a current drive) menu in SETUP mode. Follow the steps below to do so. These instructions
assume that the Time Base indication for the E-IDE hard disk appears on the display and that the recorder
section is stopped.
disk to start up as a current drive. If you wish to use the SCSI drive as a current drive, you need to set the
[Drive Sel.?] (Selecting a current drive) menu in SETUP mode. Follow the steps below to do so. These instructions
assume that the Time Base indication for the E-IDE hard disk appears on the display and that the recorder
section is stopped.
1. Press the DISP SEL key twice to enter SETUP mode.
2. Press the EXECUTE/YES key.
The D-108 enters SETUP mode and shows the SETUP mode menu used prior to shutdown.
With the default setting, the [Signature Set?] menu appears.
With the default setting, the [Signature Set?] menu appears.
3. Turn the JOG dial to select the [Drive Sel.?] menu and press the EXECUTE/YES key.
[IDE] flashes, indicating the IDE disk is currently selected.
4. Turn the JOG dial clockwise to select [SCSI#] and press the EXECUTE/YES key.
SCSI (“#” represents the SCSI ID of the SCSI drive) is selected as a current drive.
When the SCSI drive is selected as a current drive,
the Program number’s prefix changes from “P” to
“S.”
5. Press the EXIT/NO key or the STOP button.
The D-108 exits SETUP mode and indicates the top of the Program on the SCSI disk (ABS 0).
If you wish to switch the current drive from the SCSI drive to the E-IDE hard disk, turn off and on the
power to the D-108, or use the [Drive Sel.?] menu as explained above.
power to the D-108, or use the [Drive Sel.?] menu as explained above.
44.1kHz
SETUP
8
7
6
5
4
3
2
1
42
OL
0
30
24
18
12
9
6
3
∞
44.1kHz
SETUP
8
7
6
5
4
3
2
1
42
OL
0
30
24
18
12
9
6
3
∞