Chamberlain MUGAPLM User Manual
7
PIN Number Functions
PIN number Function
01
01
Self Test Mode
03
Power-save Mode
04
Exit Power-save Mode
05 01 Call
Enable MUGAPLM Learn Mode
06 (1-3)
MUGAPLM Volume Control
07 (1-3)
MUGAPLM Microphone Sensitivity
7 ### PIN
Removing PIN Numbers
08 (1-3)
MUGAPLM Brightness Control
8 (1-4)
Activating a Remote Control
Remote (1-4) Transmitter
09 ### PIN
09 ### PIN
Change the Master PIN Number
9 PIN
Add PIN Numbers
9 PIN (1-4)
Add PIN Numbers with GCU
restrict
restrict
51 PIN
Add Temporary PIN Number
51 PIN (1-4)
Add Temporary PIN Number with
GCU restrict
GCU restrict
52 Vacation
Mode
53
Exit Vacation Mode
54 Party
Mode
55 (1-3)
Alternate Channel Set
56
Place MUGAPLM in Multi-GAP
Passive Mode
Passive Mode
57
Place MUGAPLM back to Active
Mode
Mode
58
Default GCU #3 to the Passive
MUGAPLM
MUGAPLM
59
Default GCU #4 to the Passive
MUGAPLM
MUGAPLM
The Passive MUGAPLM defaults to activating GCU #2
when it is activated by a PIN Number entered on that
keypad, a near-by Remote Control Transmitter, or if the
Call button is pressed.
To have the Passive MUGAPLM activate GCU #3:
when it is activated by a PIN Number entered on that
keypad, a near-by Remote Control Transmitter, or if the
Call button is pressed.
To have the Passive MUGAPLM activate GCU #3:
Enter Master PIN Number on Passive MUGAPLM:
?
?
?
?
5
8
To have the Passive MUGAPLM activate GCU #4:
Enter Master PIN Number on Passive MUGAPLM:
?
?
?
?
5
9
Multi-GAP Default GCU Setting
“BEEP”
“BEEP”
The AA batteries (not provided) in the GCU will last
up to a year and a half depending on use (Lithium
batteries recommended for colder environments.) If
batteries are low, the intercom will beep three times
after it is activated.
The C batteries (not provided) in the MUGAPLM will
last up to a year and a half with all functions enabled.
Not activating remote control transmitters and
enabling the Power-save Mode can extend battery life
up to five years.
NOTE: To prevent damage to the circuit DO NOT use
C size Lithium batteries. If Lithium batteries are
needed, switch the C battery pack with the provided
AA battery pack.
up to a year and a half depending on use (Lithium
batteries recommended for colder environments.) If
batteries are low, the intercom will beep three times
after it is activated.
The C batteries (not provided) in the MUGAPLM will
last up to a year and a half with all functions enabled.
Not activating remote control transmitters and
enabling the Power-save Mode can extend battery life
up to five years.
NOTE: To prevent damage to the circuit DO NOT use
C size Lithium batteries. If Lithium batteries are
needed, switch the C battery pack with the provided
AA battery pack.
Battery
To open a gate enter any valid PIN Number on
MUGAPLM.
For multiple GCU’s, enter the PIN Number followed
by the GCU Identity (1-4).
For a Remote Control Transmitter, hold down the
corresponding numbered button for 5 seconds (within
75' of MUGAPLM).
On intercom, press the Remote button while talking to
a visitor. At other times, hold the intercom’s Remote
button for 10 seconds, to activate the Primary GCU.
NOTE: When using a MUOTIU or MUOTIU-EX press
“0” to answer a call.
On a OTIU or MUOTIU, dial “*9” on on the telephone,
while talking to a visitor.
MUGAPLM.
For multiple GCU’s, enter the PIN Number followed
by the GCU Identity (1-4).
For a Remote Control Transmitter, hold down the
corresponding numbered button for 5 seconds (within
75' of MUGAPLM).
On intercom, press the Remote button while talking to
a visitor. At other times, hold the intercom’s Remote
button for 10 seconds, to activate the Primary GCU.
NOTE: When using a MUOTIU or MUOTIU-EX press
“0” to answer a call.
On a OTIU or MUOTIU, dial “*9” on on the telephone,
while talking to a visitor.
Open Gate
To make a call dial the directory code then press the
Call button.
To answer a call press “0” on the phone connected to
the OTIU or MUOTIU.
Call button.
To answer a call press “0” on the phone connected to
the OTIU or MUOTIU.
To Answer or Make Call