JVC SR-DVM700U User Manual
52
EN
EDITING
You can use a camcorder as the source player and your unit as the
recording deck. If your camcorder has a DV IN/OUT connector, you
can use the camcorder as the recording deck and your unit as the
source player.
recording deck. If your camcorder has a DV IN/OUT connector, you
can use the camcorder as the recording deck and your unit as the
source player.
1
Make connections.
A If the camcorder has no S-VIDEO output connector:
^ connect the camcorder’s AUDIO/VIDEO OUTPUT
connectors to the unit’s [VIDEO/AUDIO ((MONO) L/R)] input
connectors on the front panel.
connectors on the front panel.
●
When using a monaural camcorder, connect its AUDIO OUT
connector to the [AUDIO-L] input connector on your unit.
connector to the [AUDIO-L] input connector on your unit.
B If the camcorder has an S-VIDEO output connector:
^ connect the camcorder’s AUDIO OUT and S-VIDEO OUT
connectors to the unit’s [AUDIO] and [S-VIDEO] input
connectors on the front panel.
connectors on the front panel.
C If the camcorder has a DV IN/OUT connector:
^ connect the camcorder’s DV IN/OUT connector to the unit’s
[DV IN/OUT] connector.
●
When using your unit as the source player, refer to the
camcorder’s instruction manual for the recording procedure.
camcorder’s instruction manual for the recording procedure.
2
Press DV/HDD/DVD on the unit repeatedly to select the
recording deck.
recording deck.
3
Press INPUT SELECT +/– on the remote control or
INPUT SELECT on the unit to select
INPUT SELECT on the unit to select
AF-1B or ADVB.
●
Set
AFRONT AUX F-1B to AVIDEOB for the [VIDEO] input
connector, or
AS-VIDEOB for the [S-VIDEO] input connector,
depending on the connector being used. (
A pg. 62)
4
Press REC MODE repeatedly to set the recording mode. For
DV deck, press REC MODE on the remote control to set the
recording mode.
DV deck, press REC MODE on the remote control to set the
recording mode.
5
Start playback on the camcorder slightly before the actual point
from where you wish to start dubbing.
from where you wish to start dubbing.
6
Press
R on the unit to start recording. Or while holding R, press
I on the remote control. The dubbing starts.
7
Press
o on the unit, then stop playback on the camcorder.
NOTES:
●
All necessary cables can be obtained from your dealer.
●
Refer to the camcorder’s instruction manual for operating
procedure.
procedure.
●
The quality of dubbed picture becomes poorer than that of the
original.
original.
●
When you are editing through the [DV IN/OUT] connector, the
unit will stop if the player begins playing a blank portion of tape or
the signal is interrupted.
unit will stop if the player begins playing a blank portion of tape or
the signal is interrupted.
●
When connecting the unit to a device equipped with a DV input
connector, be sure to use the optional DV cable (VC-VDV 204U).
connector, be sure to use the optional DV cable (VC-VDV 204U).
●
To edit through the [DV IN/OUT] connector using the HDD or
DVD deck, refer to
DVD deck, refer to
ADV Dubbing (HDD & DVD Deck Only)B
(
A pg. 50).
●
When using your unit as the recording deck, chapters (marks)
can be automatically created. Set
can be automatically created. Set
ADV AUTO CHAPTERINGB to
AONB. (A pg. 61)
Edit From A Camcorder
A If the camcorder has no S-VIDEO output connector:
Recorder
Player
To [VIDEO/AUDIO
((MONO) L/R)] input
((MONO) L/R)] input
Audio/video cable
(not supplied)
(not supplied)
AUDIO/VIDEO OUTPUT
B If the camcorder has an S-VIDEO output connector:
To
[S-VIDEO]
input
To [AUDIO] input
S-video cable
(not supplied)
(not supplied)
AUDIO OUTPUT
Audio cable
(not
supplied)
(not
supplied)
S-VIDEO
OUTPUT
OUTPUT
Recorder
Player
C If the camcorder has a DV IN/OUT connector:
To [DV IN]
DV cable
(VC-VDV 204U)
(not supplied)
DV connector
Player/Recorder
Recorder/Player
●
Slide the TV/DVD switch to DVD.