JVC DR-M1SLB User Manual

Masterpage:Right-No-Heading

Filename [DR-M1EK_10Editing.fm]

Page 85

September 3, 2003 2:14 pm

Set “L-2 SELECT” to the appropriate mode depending on the 
type of appliance connected to the unit’s L-2 IN/DECODER 
connector.

A

(The boldface settings in the table below indicate the settings at 
your purchase.)

B

Press SET UP.

● If you have a satellite receiver or a decoder connected to the 

L-2 IN/DECODER connector, be sure to set “L-2 SELECT” back 
to appropriate mode after editing.

● If you are not connecting a satellite receiver or a decoder to 

the L-2 IN/DECODER connector, leave “L-2 SELECT” set to 
“VIDEO”.

● When “L-2 SELECT” is set to “SAT VIDEO” and “SAT 

S-VIDEO”, “SAT” appears on the TV screen or front display 
panel instead of “L-2”.

● If “L-1 OUTPUT” is set to “SCART S-VIDEO”, it is not possible 

to set “L-2 SELECT” to “DECODER” or “SAT VIDEO”.

● If “L-1 OUTPUT” is set to “SCART RGB”, it is not possible to 

set “L-2 SELECT” to “DECODER” or “SAT S-VIDEO”.

● If “L-1 OUTPUT” is set to “COMPONENT” and “L-2 SELECT” 

to “SAT VIDEO”, “SAT S-VIDEO” or “DECODER”, be sure to 
connect the L-1 IN/OUT connector with a TV.

Set “F-1 INPUT” to the appropriate mode depending on the 
connector (VIDEO or S-VIDEO) being used on the front panel.

A

(The boldface settings in the table below indicate the settings at 
your purchase.)

B

Press SET UP.

Perform steps

A Press rt to move the 

arrow to “L-2 SELECT”, 
then press ENTER.

B Press rt to select the 

appropriate setting, then 
press ENTER.

8 L-2 SELECT

Select “VIDEO” or “S-VIDEO” to use this unit as the 
recording deck with the player connected to the L-2 IN/
DECODER connector, or to use the satellite receiver 
connected to the L-2 IN/DECODER connector.

:

If a connected appliance’s output is 
compatible only with regular video 
signals, set to “VIDEO”.

S-VIDEO

:

If a connected appliance’s output is 
compatible with Y/C signals, set to 
“S-VIDEO”. You can obtain high-
quality picture. (For connection, be 
sure to use a 21-pin SCART cable 
that is compatible with the Y/C 
signal.)

Select “SAT VIDEO” or “SAT S-VIDEO” to view a satellite 
programme with the TV set while the unit is turned off. 
(

SAT VIDEO

:

If a connected satellite receiver’s 
output is compatible only with 
regular video signals, set to “SAT 
VIDEO”.

SAT S-VIDEO

: If a connected satellite receiver’s 

output is compatible with Y/C 
signals, set to “SAT S-VIDEO”. You 
can obtain a high-quality S-VHS 
picture. (For connection, be sure to 
use a 21-pin SCART cable that is 
compatible with the Y/C signal.)

DECODER

:

To use a decoder connected to the 
L-2 IN/DECODER connector.

Perform steps

A and B of “L-1 Output and L-1 Input Setting 

(L-1 OUTPUT and L-1 INPUT)” on page 84.

A Press rt to move the 

arrow to “F-1 INPUT”, 
then press ENTER.

B Press rt to select the 

appropriate setting, then 
press ENTER.

8

:

When connecting an appliance to 
the VIDEO input connector, set to 
“VIDEO”.

S-VIDEO

:

When connecting an appliance to 
the S-VIDEO input connector, set to 
“S-VIDEO”.

DR-M1EK_10Editing.fm  Page 85  Wednesday, September 3, 2003  2:18 PM