Daewoo DHR-8100P User Manual
If your cable wire is connected to your TV without a
converter or descrambler box, unscrew the wire
from your TV and attach it to the RF IN (FROM ANT.)
jack on the rear panel of the HDD/DVD Recorder.
Use the supplied RF cable to connect between the
HDD/DVD Recorder’s OUT (TO TV) jack and the
antenna input jack on your TV. With this connection,
you can receive all midband, superband, and
hyperband channels (all cable channels).
converter or descrambler box, unscrew the wire
from your TV and attach it to the RF IN (FROM ANT.)
jack on the rear panel of the HDD/DVD Recorder.
Use the supplied RF cable to connect between the
HDD/DVD Recorder’s OUT (TO TV) jack and the
antenna input jack on your TV. With this connection,
you can receive all midband, superband, and
hyperband channels (all cable channels).
Connecting a TV
Choose one of the following TV connections,
depending on the capabilities of your equipment.
depending on the capabilities of your equipment.
RF Connection
Connect the ANT OUT (TO TV) jack on the HDD/DVD
Recorder to the antenna in jack on your TV using the
supplied 75-ohm RF cable (R).
Recorder to the antenna in jack on your TV using the
supplied 75-ohm RF cable (R).
Scart Connection
1
1
Plug a scart cable into the scart socket EURO
AV1 at the back of the HDD/DVD Recorder and
the corresponding scart socket at the back of
the TV set. (V)
AV1 at the back of the HDD/DVD Recorder and
the corresponding scart socket at the back of
the TV set. (V)
2
Plug a scart cable into the blue scart socket
EURO AV2/DECODER at the back of the
HDD/DVD Recorder and the corresponding
scart socket at the back of the Decoder.
EURO AV2/DECODER at the back of the
HDD/DVD Recorder and the corresponding
scart socket at the back of the Decoder.
INTRODUCTION
15
Connections
Connections
Connecting Antenna/Cable
1
Disconnect the antenna/cable from the rear of
your TV.
your TV.
2
Connect this cable to the jack marked ANT IN
(FROM ANT.) on the rear panel of the HDD/DVD
Recorder.
(FROM ANT.) on the rear panel of the HDD/DVD
Recorder.
• There are a variety of ways to connect the
HDD/DVD Recorder to your TV and other
equipment. Use only one of the connections
described below. Whichever TV connection
you use will work with all input sources.
equipment. Use only one of the connections
described below. Whichever TV connection
you use will work with all input sources.
• Please refer to the manuals for your TV, VCR,
stereo system, or other devices as necessary to
make the best connections.
make the best connections.
• For better sound reproduction, connect the
HDD/DVD Recorder’s AUDIO OUT jacks to the
audio in jacks of your amplifier, receiver,
stereo, or audio/video equipment. See
‘Connecting an Amplifier/Receiver‘ on page 16.
audio in jacks of your amplifier, receiver,
stereo, or audio/video equipment. See
‘Connecting an Amplifier/Receiver‘ on page 16.
Caution
• Make sure the HDD/DVD Recorder is
connected directly to the TV, and the TV is set
to the correct video input.
to the correct video input.
• Do not connect the HDD/DVD Recorder’s
AUDIO OUT jack to the phone in jack (record
deck) of your audio system.
deck) of your audio system.
• Do not connect the HDD/DVD Recorder via
your VCR. The DVD image could be distorted
by the copy protection system.
by the copy protection system.
Antenna
Antenna
Cable TV
Wall Jack
Wall Jack
Flat Wire
(300ohm)
(300ohm)
300/75ohm Adapter
(Not supplied)
OR
OR
Rear of HDD/DVD Recorder
CONNECTIONS
ANTENNA
INPUT
Y
Pb
Pr
COMPONENT/PROGRESSIVE VIDEO INPUT
S-VIDEO
INPUT
R
V
S
C
Rear of HDD/DVD Recorder
Rear of TV
This set doesn’t have a modulator output. However
it still applies the RF through Output.
it still applies the RF through Output.
DG-M22-12D1P-XA(GB) 2005.12.22 8:4 AM ˘
` 15 mac001 1200DPI 100LPI