Sony MF68-00258A User Manual
GB-4
D
I
G
I
T
A
L
S
A
T
E
L
L
I
T
CONNECTING YOUR "STB"
1. LOCATION OF THE RECEIVER
Your STB should be placed under proper ventilation.
Don’t put in completely enclosed cabinet that will restrict the flow of air, resulting in
overheating.
The location should be safeguarded from direct sunlight, excess moisture, rough
handling or household pets.
Avoid stacking other electronic components on the top of the receiver.
The location should be safely accessible by the cable from your antenna system.
Don’t put in completely enclosed cabinet that will restrict the flow of air, resulting in
overheating.
The location should be safeguarded from direct sunlight, excess moisture, rough
handling or household pets.
Avoid stacking other electronic components on the top of the receiver.
The location should be safely accessible by the cable from your antenna system.
2. CONNECTING THE RECEIVER WITH DISH SYSTEM
After installing your antenna system, connect the coaxial cable from the LNB of your
antenna to "LNB" terminal marked at the rear of the STB.
All cable connectors should be finger tightened; do not use any kind of wrench while
tightenning connectors. The cable should be 75ohm impedance coaxial twisted at
the end with an "F" type connector.
antenna to "LNB" terminal marked at the rear of the STB.
All cable connectors should be finger tightened; do not use any kind of wrench while
tightenning connectors. The cable should be 75ohm impedance coaxial twisted at
the end with an "F" type connector.
3. CONNECTING THE RECEIVER TO TV
To connect the receiver with your television, you can use four methods;
via SCART cable, RF cable, RCA cable or S-VHS cable. S-VHS provides the better
screen quality.
Connect the RF cable to the terminal marked "TV" at the rear panel of STB and its other
end to the TV RF input socket.
In the case of connecting your TV through SCART cable, connect the SCART connector
marked TV to the respective SCART port on the TV.
via SCART cable, RF cable, RCA cable or S-VHS cable. S-VHS provides the better
screen quality.
Connect the RF cable to the terminal marked "TV" at the rear panel of STB and its other
end to the TV RF input socket.
In the case of connecting your TV through SCART cable, connect the SCART connector
marked TV to the respective SCART port on the TV.
4. CONNECTING YOUR ANALOG RECEIVER
To facilitate the user using analog receiver to view analog channels, STB has been
provided with a loop through terminal marked as "LOOP".
Connect the coaxial cable from this terminal to the IF input terminal of your analog
receiver. Now by keeping the STB in standby, you will be able to tune and view analog
channels from your analog receiver.
provided with a loop through terminal marked as "LOOP".
Connect the coaxial cable from this terminal to the IF input terminal of your analog
receiver. Now by keeping the STB in standby, you will be able to tune and view analog
channels from your analog receiver.
5. CONNECTING YOUR VCR
To connect a VCR or DVD player, the STB has been provided with SCART at the rear
marked "AV2".
Using a SCART connector, the VCR or DVD player can be connected to the receiver.
marked "AV2".
Using a SCART connector, the VCR or DVD player can be connected to the receiver.
N
No
otte
e
: This is supported by standby.
6. CONNECTING EXTERNAL AUDIO / HI-FI SYSTEM
To connect any external Audio Hi-Fi system, the receiver has been provided
with two RCA connectors at the back of the receiver, marked with AUDIO L and R
respectively to connect the left and right Audio.
with two RCA connectors at the back of the receiver, marked with AUDIO L and R
respectively to connect the left and right Audio.
DSR 9500/9510 2.28 3/5/03 3:33 PM Page 4