Siemens 20 User Manual
administration.fm
A31003-O1010-M100-9-76A9, 05/05/2008
HiPath 8000 - OpenStage Family, Administration Manual
HiPath 8000 - OpenStage Family, Administration Manual
3-5
Administration
LAN Settings
3.2
LAN Settings
3.2.1
LAN Port Settings
The OpenStage phone provides an integrated switch which connects the LAN, the phone itself
and a PC port. By default, the switch will auto negotiate transfer rate (10/100 Mb/s, 1000 Mb/s
with OpenStage 60/80 G) and duplex method (full or half duplex) with whatever equipment is
connected. Optionally, the required transfer rate and duplex mode can be specified manually
using the LAN port speed parameter.
and a PC port. By default, the switch will auto negotiate transfer rate (10/100 Mb/s, 1000 Mb/s
with OpenStage 60/80 G) and duplex method (full or half duplex) with whatever equipment is
connected. Optionally, the required transfer rate and duplex mode can be specified manually
using the LAN port speed parameter.
The PC Ethernet port is controlled by the PC port mode parameter. If set to "Disabled", the PC
port is inactive; if set to "Enabled", it is active. If set to "Mirror", the data traffic at the LAN port
is mirrored at the PC port. This setting is for diagnostic purposes. If, for instance, a PC running
Ethereal/Wireshark is connected to the PC port, all network activities at the phone’s LAN port
can be captured.
port is inactive; if set to "Enabled", it is active. If set to "Mirror", the data traffic at the LAN port
is mirrored at the PC port. This setting is for diagnostic purposes. If, for instance, a PC running
Ethereal/Wireshark is connected to the PC port, all network activities at the phone’s LAN port
can be captured.
When PC port autoMDIX is enabled, the switch determines automatically whether a regular
MDI connector or a MDI-X (crossover) connector is needed, and configures the connector ac-
cordingly.
MDI connector or a MDI-X (crossover) connector is needed, and configures the connector ac-
cordingly.
Data required
•
LAN port speed / LAN port type: Settings for the ethernet port connected to a LAN
switch.
switch.
Value range: "Automatic," "10 Mbps half duplex", "10 Mbps full duplex", "100 Mbps half du-
plex", "100 Mbps full duplex", "1 Gbps half duplex" (OpenStage 60/80 G), "1 Gbps full du-
plex" (OpenStage 60/80 G).
plex", "100 Mbps full duplex", "1 Gbps half duplex" (OpenStage 60/80 G), "1 Gbps full du-
plex" (OpenStage 60/80 G).
Default: "Automatic".
•
PC port speed / PC port type: Settings for the ethernet port connected to a PC.
Value range: "Automatic", "10 Mbps half duplex", "10 Mbps full duplex", "100 Mbps half du-
plex", "100 Mbps full duplex", "1 Gbps half duplex" (OpenStage 60/80 G), "1 Gbps full du-
plex" (OpenStage 60/80 G).
plex", "100 Mbps full duplex", "1 Gbps half duplex" (OpenStage 60/80 G), "1 Gbps full du-
plex" (OpenStage 60/80 G).
Default: "Automatic".
•
PC port mode / PC port status: Controls the PC port.
Value range: "disabled", "enabled", "mirror".
Default: "disabled".
>
In the default configuration, the LAN port supports automatic detection of cable con-
figuration (pass through or crossover cable) and will reconfigure itself as needed to
connect to the network. If the phone is set up to manually configure the switch port
settings, the cable detection mechanism is disabled. In this case, care must be taken
to use the correct cable type.
figuration (pass through or crossover cable) and will reconfigure itself as needed to
connect to the network. If the phone is set up to manually configure the switch port
settings, the cable detection mechanism is disabled. In this case, care must be taken
to use the correct cable type.