TELEDEX 600-0480-59 Leaflet

Check to be sure that you have all of the following components in

your package (see figure below) :

• Telephone base unit

• Handset coil cord

• User guide

• Handset

• Line cord

1) Plug one end of the handset coiled cord into the handset. Plug 

the other end of the cord into the handset jack located on the 

left side of the phone base.  (Refer to diagram on reverse.)

2) Place the handset in the handset cradle. Plug one end of the line 

cord into the 

jack on the back of your phone.

3) Plug the other end of the modular cord into the wall jack.

The Pearl S telephone can easily be attached to a wall mount plate.

1) Remove the wall mount clip (located on the front of the

telephone, above the speaker grill) by firmly pushing upward 

(toward the hook switch.)

2) Rotate the clip 180 degrees, so that the side with the protruding 

edge is towards the top of the telephone. This edge will help 

hold the handset on the cradle. 

3) Place the handset in the handset cradle.

4) Connect the line cord into the 

jack on the back of your 

phone. Route the line cord through channel on the bottom of 

the telephone. Connect the other end of the line cord to the 

jack on the wall mount plate.

5) Slip the phone onto the wall plate; slide the telephone down 

so it is firmly in place.

The data port is located on the right hand side of the telephone. Use

this jack to connect a computer or fax machine in parallel to the

same phone line to which the telephone is connected.

Your Pearl S telephone has two ringer volume levels: “Low” and

“High.” To adjust the ringer volume, slide the ringer volume switch

(located on the backside of the telephone) to the desired level.

There are three (3) volume levels for the handset volume. To increase

or decrease the handset volume, slide the handset volume switch

(located on the right hand side of the telephone) to the desired setting.

To increase or decrease the speakerphone volume, move the speaker

volume slider control (located on the right hand side of the telephone)

until speaker volume is at a satisfactory level.

To make a call, pick up the handset or press the 

key. When

you hear the dial tone, dial the desired phone number. To answer an

incoming call, pick up the handset or press the 

key. To end a

call, place the handset back on the base, or press the 

key

again.

To switch from the handset to the speakerphone during a call, press

the 

key, and place the handset on the base. To switch from

the speakerphone to the handset, lift the handset; the speakerphone

will automatically turn off. 

The redial function allows you to redial the last dialed number. Pick

up the handset, or press the 

key, and press the 

key. The

number will be dialed automatically.

Flash supports custom calling services, such as call waiting. For

example, if you have subscribed to call waiting, press 

to answer

an incoming call, without disconnecting the current call. Press 

again to return to the first call.

To place a call on hold, press the 

key. The 

LED flashes.

You may now hang up the handset without disconnecting the call.

To resume the call, press the 

key again, or press the 

key.

The call will once again be active.

Pressing the 

key will silence the handset or speakerphone micro-

phone. You will be able to hear the other party, but they will not be

able to hear you. The 

LED will light. Press the 

key again to

resume your conversation.

Follow these steps to program a number into one of the three memory

locations, for one-touch access to guest services, or for accessing

special PBX/Centrex services or features. Each memory location can

store up to sixteen (16) digits.

1) Lift the handset, then press the 

key (For key location,

refer to diagram on reverse.)

2) On the dial pad, enter the number you wish to store. Once 

you have entered the number completely, press the memory

button corresponding to the desired location.

Pick up the handset or press the 

key, wait for a dial tone,

then press the desired memory (guest service) key. The telephone will

automatically dial the stored number. 

The message waiting indicator flashes to indicate that there is a

message waiting. Consult your system administrator or service

provider for instructions on how to access these messages.

Your Pearl S telephone has been designed to provide years of trouble

free service. To ensure its longevity, please follow these maintenance

instructions:

1) Keep the Pearl S away from heat, as high temperatures can shorten

the life of the electrical components, and distort or melt plastic 

parts.

2) The telephone should be kept free of dust and moisture.  If it 

gets wet, wipe it dry immediately. Liquids may contain minerals 

that can corrode electronic circuits.

3) Handle your telephone gently and carefully.  Dropping it can 

cause serious damage to internal circuitry or the plastic case, 

which may result in malfunction.

4) Do not use any type of chemical or abrasive powder to clean the

outer casing.  Use only mild detergents on a soft, damp cloth to 

clean the telephone.

5) In case of trouble with the telephone, do not attempt to repair 

the telephone yourself. Contact your distributor for assistance.  

If the trouble is affecting the telephone lines, the phone company

or service provider may ask you to disconnect the telephone 

until the problem is resolved.