Telular SX5T CDMA User Manual
Phonecell
®
SX5T CDMA2000
30
User Manual
Sending/Receiving Circuit Switched Data
A PC with a serial, USB or phone (RJ11) connection to the SX5T can send and receive circuit
switched data using the SX5T. Check with your service provider to see if your account supports
circuit switched data transfer.
switched data using the SX5T. Check with your service provider to see if your account supports
circuit switched data transfer.
Set Your Computer’s Port and Modem Speeds for Circuit Switched Data
To send or receive circuit switched data, you need to set the port and modem speeds your
computer uses for the SX5T to 115200 bps. See Windows XP/2000 Setup (page 18) or
Windows 98 Setup (page 24) for details. This is the communication speed between the
computer and SX5T; actual data transfer rates will be slower.
computer uses for the SX5T to 115200 bps. See Windows XP/2000 Setup (page 18) or
Windows 98 Setup (page 24) for details. This is the communication speed between the
computer and SX5T; actual data transfer rates will be slower.
Choose Data Mode
1.
To receive one data transfer, enter
Data Next Call mode. Press
.
Your SX5T will treat the next incoming call as data, then return to normal operation.
If you are using an RJ11 port to receive the data, you may skip the remaining steps.
If you are using an RJ11 port to receive the data, you may skip the remaining steps.
2.
To receive data indefinitely, enter
Data Always mode. Press
.
(Your SX5T will treat all incoming calls as data. To resume receiving voice calls, you must switch
back to
Voice mode: Press
. If you wish to make a single voice call while
remaining in Data Always mode, press
.)
If you are using an RJ11 port to receive the fax, you may skip the remaining steps.
3.
To send circuit switched data, set the Data Port and Baud Rate, then follow your service
provider’s directions for sending circuit switched data. Whenever your software asks you what
modem to use, select the
provider’s directions for sending circuit switched data. Whenever your software asks you what
modem to use, select the
Standard 19200 Modem.
(For Windows XP and Windows 2000, you can start by opening
Control Panel > Network and
Dial Up Connections, then double-clicking on Make New Connection to start the Network
Connection Wizard.)
Connection Wizard.)
(For Windows 98, you can start by running
Dial-Up Networking and double-clicking on Make
New Connection.)
Choose the SX5T’s Data Port
1.
Enter Configuration Mode – Press
<lock code>
.
2.
Select
Data Port – Press
.
– OR –
Select
RJ11 Port – Press
.
3.
If you selected
Data Port, select which Data port to use.
Select
Serial by pressing
.
– OR –
Select
USB by pressing
(Windows XP/2000 only).
Set the SX5T’s Baud Rate for Circuit Switched Data
1.
Enter Configuration Mode – Press
<lock code>
.
2.
Select Baud Speed 115200 – Press
.
Note:
If you take the phone off-hook while sending or receiving circuit switched data via serial or USB cable,
you will hear a busy tone; the data transmission/reception will not be disrupted.
If you take the phone off-hook while sending or receiving circuit switched data using an RJ11 phone
jack connection, the fax data transmission/reception may be disrupted.
you will hear a busy tone; the data transmission/reception will not be disrupted.
If you take the phone off-hook while sending or receiving circuit switched data using an RJ11 phone
jack connection, the fax data transmission/reception may be disrupted.
#
5
*
6
3
1
*
#
#
*
0
*
#
#
1
*
5
3
1
*
#
#
0
*
5
3
1
*
#
#
1
*
3
1
1
*
#
#
0
*
3
1
1
*
#
#
*
0
*
#
#
4
*
#
#
7
*
#
#
6
*
#
#
2
*
#