TELEDEX SIP LD4110S User Manual

WHEN USING YOUR TELEPHONE EQUIPMENT, BASIC SAFETY  
PRECAUTIONS SHOULD ALWAYS BE FOLLOWED TO REDUCE THE  
RISK OF FIRE, ELECTRIC SHOCK AND INJURY TO PERSONS, INCLUDING 
THE FOLLOWING:
1.  READ AND UNDERSTAND ALL INSTRUCTIONS.
2.  FOLLOW ALL WARNINGS AND INSTRUCTIONS MARKED ON  
 

THE PRODUCT.

3.   UNPLUG THE PRODUCT FROM THE WALL OUTLET BEFORE  
 

CLEANING. DO NOT USE LIQUID CLEANER  OR  

 

AEROSOLCLEANERS. USE A DAMP CLOTH FOR CLEANING.

4.  DO NOT USE THIS PRODUCT NEAR WATER; FOR EXAMPLE NEAR 
 

A BATHTUB, WASH BOWL, KITCHEN SINK OR LAUNDRY TUB, IN 

 

A WET BASEMENT, OR NEAR A SWIMMING POOL.

5.  DO NOT PLACE THIS PRODUCT ON AN UNSTABLE CART, STAND 
 

OR TABLE. THE PRODUCT MAY FALL, CAUSING SERIOUS DAMAGE  

 

TO THE PRODUCT.

6.  SLOTS AND OPENINGS IN THE CABINET AND THE BOTTOM ARE
 

PROVIDED FOR VENTILATION, TO PROTECT IT FROM 

 

OVERHEATING. THESE OPENINGS MUST NOT BE BLOCKED OR  

 

 

COVERED. THE OPENINGS SHOULD NEVER BE BLOCKED BY 

 

PLACING THE PRODUCT ON A BED, SOFA, RUG OR ANY OTHER

 

SIMILAR SURFACE. THIS PRODUCT SHOULD NEVER BE PLACED  

 

 

NEAR OR OVER A RADIATOR OR HEAT REGISTER. THIS 

 

PRODUCT SHOULD NOT BE PLACED IN A BUILT-IN INSTALLATION   

 

UNLESS PROPER VENTILATION IS PROVIDED.

7.  NEVER PUSH OBJECTS OF ANY KIND INTO THIS PRODUCT  

 

 

THROUGH CABINET SLOTS AS THEY MAY TOUCH DANGEROUS 

 

VOLTAGE POINTS OR SHORT OUT PARTS THAT COULD RESULT IN   

 

A RISK OF FIRE OR ELECTRIC SHOCK. NEVER SPILL LIQUID OF ANY 

 

KIND ON THE PRODUCT.

8.  TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT DISASSEMBLE  
 

THIS PRODUCT, BUT TAKE IT TO QUALIFIED SERVICE PERSONNEL   

 

WHEN SOME SERVICE OR REPAIR WORK IS REQUIRED. OPENING 

 

OR REMOVING COVERS MAY EXPOSE YOU TO DANGEROUS 

 

VOLTAGES OR OTHER RISKS. INCORRECT REASSEMBLY CAN CAUSE  

 

ELECTRIC SHOCK WHEN THE APPLIANCE IS SUBSEQUENTLY USED.

9.  UNPLUG THIS PRODUCT FROM THE WALL OUTLET AND REFER
 

SERVICING TO QUALIFIED SERVICE PERSONNEL UNDER THE 

 

FOLLOWING CONDITIONS:

 

– WHEN THE POWER SUPPLY CORD OR PLUG IS DAMAGED 

 

  OR FRAYED.

 

– IF LIQUID HAS BEEN SPILLED INTO THE PRODUCT.

 

– IF THE PRODUCT HAS BEEN EXPOSED TO RAIN OR WATER.

 

– IF THE PRODUCT DOES NOT OPERATE NORMALLY BY 

 

  FOLLOWING THE OPERATING INSTRUCTIONS. ADJUST ONLY  

 

 

  THOSE CONTROLS THAT ARE COVERED BY THE OPERATING 

 

  INSTRUCTIONS, AS IMPROPER ADJUSTMENT OF OTHER 

 

  CONTROLS MAY RESULT IN DAMAGE AND WILL OFTEN 

 

  REQUIRE EXTENSIVE WORK BY A QUALIFIED TECHNICIAN 

 

  TO RESTORE THE PRODUCT TO NORMAL OPERATION.

 

– IF THE PRODUCT HAS BEEN DROPPED OR THE CABINET HAS  

 

 

  BEEN DAMAGED.

 

– IF THE PRODUCT EXHIBITS A DISTINCT CHANGE IN 

 

  PERFORMANCE.

10. AVOID USING A TELEPHONE (OTHER THAN A CORDLESS TYPE)    
 

DURING AN ELECTRICAL STORM. THERE MAY BE A RISK OF 

 

ELECTRIC SHOCK FROM LIGHTNING.

NOTICES
REQUIREMENTS OF PART 15 - FCC RULES

NOTE: This equipment has been tested and found to comply with  
the limits for a Class A digital device, pursuant to Part 15 of the  
FCC Rules. These limits are designed to provide reasonable protection 
against harmful interference in a residential installation. This  
equipment generates, uses, and can radiate radio frequency energy 
and, if not installed and used in accordance with the instructions, 
may cause harmful interference to radio communications. However, 
there is no guarantee that interference will not occur in a particular 
installation. If this equipment does cause harmful interference to 
radio or television reception, which can be determined by turning 
the equipment off and on, the user is encouraged to try to correct 
the interference by one or more of the following measures: a) move 
the telephone away from the receiver; b) consult the dealer or an 
experienced radio/TV technician for help. Any changes made by the 
user not approved by the manufacturer can void the user’s authority 
to operate the telephone.

For Models

SIP LD4105S, SIP LD4110S
SIP LD4205S, SIP LD4210S