Panasonic KX-TCD560NZ User Manual
Multi-unit Operation
41
Operating additional units
Additional handsets
Up to 6 handsets can be registered to a
single base unit. Additional handsets will
give you the freedom to, for example, have
an intercom call with another handset while
a third handset is on an outside call. See
page 4 for information on ordering additional
handsets.
single base unit. Additional handsets will
give you the freedom to, for example, have
an intercom call with another handset while
a third handset is on an outside call. See
page 4 for information on ordering additional
handsets.
Additional base units
Handsets can be registered to up to 4 base
units, allowing you to add additional base
units and extend the area in which your
handset(s) can be used. If a handset moves
out of range of its base unit when “Auto” is
selected on base unit selection (page 41), it
will look for another base unit to make or
receive calls. A base unit and the handsets it
communicates with is called a “radio cell”.
Note:
units, allowing you to add additional base
units and extend the area in which your
handset(s) can be used. If a handset moves
out of range of its base unit when “Auto” is
selected on base unit selection (page 41), it
will look for another base unit to make or
receive calls. A base unit and the handsets it
communicates with is called a “radio cell”.
Note:
L
Calls will be disconnected when the
handset moves from one radio cell to
another.
handset moves from one radio cell to
another.
L
Intercom calls and call transfers are only
possible between handsets in the same
radio cell.
possible between handsets in the same
radio cell.
Registering a handset to a
base unit
base unit
You can register a handset to a base unit
using the following method.
using the following method.
1
Press $ (centre of joystick).
2
Select t, then press ,.
3
Select “Registration”, then press
,
,
2 times.
4
Select a base number, then press ,.
L
This number is used by the handset as
a reference only.
a reference only.
5
Press and hold {x} on the top of the
base unit for about 5 seconds, until the
registration tone sounds.
base unit for about 5 seconds, until the
registration tone sounds.
L
If all registered handsets start ringing,
press {x} to stop, then repeat this
step.
press {x} to stop, then repeat this
step.
L
After pressing {x}, the rest of this
procedure must be completed within 1
minute.
procedure must be completed within 1
minute.
6
Wait until “Enter Base PIN” is
displayed, then enter “0000” (default
base unit PIN), then press ,.
displayed, then enter “0000” (default
base unit PIN), then press ,.
L
If you changed the PIN, enter it (page
30).
30).
Note:
L
When the handset has been registered
successfully, w will stop flashing. If key
tones are turned on (page 24), a
confirmation tone will be heard.
successfully, w will stop flashing. If key
tones are turned on (page 24), a
confirmation tone will be heard.
Selecting a base unit
When “Auto” is selected, the handset will
automatically use any available base unit it
is registered to. When a specific base unit is
selected, the handset will make and receive
calls using that base unit only. If the handset
is out of range of that base unit, no calls can
be made.
automatically use any available base unit it
is registered to. When a specific base unit is
selected, the handset will make and receive
calls using that base unit only. If the handset
is out of range of that base unit, no calls can
be made.
1
Press $ (centre of joystick).
2
Select t, then press ,.
3
Select “Select Base”, then press
,
,
.
4
Select the desired base unit number, or
“Auto”, then press ,.
L
“Auto”, then press ,.
L
The handset starts searching for the
base unit.
base unit.
Cancelling a handset
A maximum of 6 handsets can be registered
to a base unit. A handset can cancel its own
registration (or the registration of another
handset) that is stored in the base unit. This
to a base unit. A handset can cancel its own
registration (or the registration of another
handset) that is stored in the base unit. This
KX-TCD560-580NZ(e).book Page 41 Tuesday, July 6, 2004 10:49 AM