Panasonic DW5100UL User Manual

31

POSITION

SHIFT

ASPECT      
ZOOM
CLOCK PHASE 
KEYSTONE

MENU SELECT

4:3

+16

SUB MENU

The position where the images are displayed can be moved here.

: The position is moved horizontally.
: The position is moved vertically.

AUTO : (For S-Video/Video signals only)

At this setting, when S1 video signals*

1

are

identified as being input to the S-Video
connector or video ID signals are identified
as being input to the video connector, the
images are displayed after automatically
being converted to the 16:9 aspect ratio.

16:9

: At this setting, when standard signals*

2

are

input, the images are converted to the 16:9
aspect ratio and displayed. When wide-screen
signals*

3

are input, the images are displayed

with their inherent aspect ratio intact.

4:3

: At this setting, when standard signals*

2

are input,

the images are displayed with their inherent aspect
ratio intact. When wide-screen signals*

3

are input,

they are converted by the PT-D5700U/PT-
D5700UL to the 4:3 aspect ratio and displayed.
With the PT-DW5100U/PT-DW5100UL, the images
are reduced in size and displayed without
converting their aspect ratio so that they will fit onto
a screen with a 4:3 aspect ratio.

S4:3

: Select this setting when using a 16:9 screen.

H FIT : Pictures are displayed using all the panel

pixels in the horizontal direction. When a
signal has an aspect ratio taller than that of
the panel pixel*

4

, the image will be displayed

with the top and bottom portions cut off.

V FIT : Pictures are displayed using all the panel

pixels in the vertical direction. When a signal
has an aspect ratio wider than that of the
panel pixel*

4

, the image will be displayed with

the left and right sides cut off.

HV FIT : The image is displayed on all the panel

pixels*

4

. When the aspect ratio of the input

signal is different from that of the panel
pixel*

4

, the signal is transformed to the aspect

ratio of the panel pixel*

4

and then displayed.

*

1

S1 video signals are 16:9 video signals to which is added the detection signal

output from the video deck or other unit which supports the wide-screen format.

*

2

Here, the standard signal means 4:3 or 5:4 input signals.

*

3

Here, the wide-screen signals means 16:9, 15:9 or 15:10 input signals.

*

4

Panel pixel aspect ratio is 4:3 in the case of PT-D5700U/PT-
D5700UL and 15:9 for PT-DW5100U/PT-DW5100UL.

• If you choose an aspect ratio that does not

match the source video’s aspect ratio, you
will see a picture with an aspect ratio not the
same as that of the original picture. Choose
the appropriate aspect ratio carefully to
match that of the original picture.

“SHARPNESS” is used to adjust the crispness of
the image.

: Sharpens the edge of the image.

: Softens the edge of the image.

In this mode, the video noise is reduced.

OFF : No correction
1

: Low

2

: Middle

3

: High

Gray scale control is exercised to suit the images,
and optimal images with a clear contrast are
projected.

ON : AI compensation is enabled.
OFF : AI compensation is disabled.

Set this according to the connected signal system.

(S-Video/Video terminal input signal)

AUTO : This is the standard setting. The

received signal system is automatically
identified.

(RGB1/RGB2 terminal input signals)

AUTO : This is the standard setting. The

received signal system is automatically
identified.

When VGA60/480p signals are input

When other than VGA60/480p are input

For the signals which are supported, refer to page
62.

AUTO

YC

B

C

R

VGA60

480pRGB

AUTO

YP

B

P

R

 (YC

B

C

R

) 

RGB

AUTO

PAL60

NTSC

SECAM

NTSC4.43

PAL-N

PAL

PAL-M

• When signal deterioration or other

factors prevent images from being
displayed correctly with the “AUTO”
setting, change the setting to match
the connected signal system.

(Continued on the next page)