Runco VX-3000D User Manual
82
VX-3000d Series Installation/Operation Manual
Y
Triggers: Select Triggers from the Service menu to configure the 12-volt trigger outputs.
You can assign one or more trigger outputs to each aspect ratio. Those triggers are then
activated by selecting that aspect ratio.
You can assign one or more trigger outputs to each aspect ratio. Those triggers are then
activated by selecting that aspect ratio.
With a VX-3000d/CineWide with AutoScope, assign at least one trigger output (the same
one to which the lens motor is connected) to the Cinema and Virtual Cinema aspect
ratios.
one to which the lens motor is connected) to the Cinema and Virtual Cinema aspect
ratios.
Miscellaneous: Select Miscellaneous from the Service menu to set the following options:
down-arrows to select the OSD Language (English, Français, Deutsch, Italiano,
Español, Svenska, Traditional Chinese, Simplified Chinese, Português or Russian).
Español, Svenska, Traditional Chinese, Simplified Chinese, Português or Russian).
which controls how long the menus remain on-screen after selecting them. Select from
5 to 60 seconds, in one-second increments. Or, set the timer to 0 (disabled) if you want
the menus to remain on-screen indefinitely.
5 to 60 seconds, in one-second increments. Or, set the timer to 0 (disabled) if you want
the menus to remain on-screen indefinitely.
• OSD Messages: When you select a new aspect ratio, input source or memory preset,
the DHD Controller briefly displays an on-screen message confirming your new
selection. To prevent the display of these messages, select OSD Messages from the
Miscellaneous menu to and set it to Off.
selection. To prevent the display of these messages, select OSD Messages from the
Miscellaneous menu to and set it to Off.
select the color that appears when no incoming signal is present. The range is from 0
to 255 inclusive for each color component (red, green and blue).
to 255 inclusive for each color component (red, green and blue).
color of the inactive image area. The range is from 0 to 255 inclusive for each color
component (red, green and blue). The inactive image area is on either side of the active
image area when using the 4:3 aspect ratio.
component (red, green and blue). The inactive image area is on either side of the active
image area when using the 4:3 aspect ratio.
• Film Mode: Use Film Mode to smooth out moving images from interlaced,
standard-definition (SD) sources. In most cases, the DHD Controller detects the proper
“pull-down” rate and vertical frequency. However, if your source is jittery and/or tearing
you may want to enable Film Mode to ensure stable processing for that source.
“pull-down” rate and vertical frequency. However, if your source is jittery and/or tearing
you may want to enable Film Mode to ensure stable processing for that source.
• CUE (Chroma Upsampling Error) Correction: Some DVD players use MPEG
decoders that do not correctly “upsample” the 4:2:0 format chroma information on the
DVD to the 4:2:2 or 4:4:4 format required by the video encoder of the display device.
DVD to the 4:2:2 or 4:4:4 format required by the video encoder of the display device.
Table 4-3. x/y Color Gamut Values
Primary
Color
Color Gamut Settings and Associated x/y Values
REC709
SMPTE “C”
EBU
x
y
x
y
x
y
Red
0.640
0.330
0.635
0.340
0.640
0.330
Yellow
0.419
0.505
0.421
0.506
0.418
0.502
Green
0.300
0.600
0.305
0.595
0.290
0.600
Cyan
0.225
0.329
0.228
0.326
0.220
0.329
Blue
0.150
0.060
0.155
0.070
0.150
0.060
Magenta
0.321
0.154
0.318
0.162
0.328
0.158