Panasonic PT-DS20KE User Manual
[PROJECTOR SETUP] menu
100 - ENGLISH
Settings
[COOLING CONDITION]
Change the fan control depending on the direction of
projection.
Set [COOLING CONDITION] correctly in accordance with
the direction of projection referencing the following figure. It
may shorten the life of the lamp if used in incorrect setting.
1) Press ▲▼ to select [COOLING
CONDITION].
2) Press the <ENTER> button.
▶
z
The
[COOLING CONDITION] screen is displayed.
3) Press ▲▼ to select a cooling condition.
：
[VERTICAL UP
SETTING]
[FLOOR
SETTING]
[CEILING
SETTING]
[VERTICAL DOWN
SETTING]
Projection direction
4) Press the <ENTER> button.
5) When the confirmation is displayed,
5) When the confirmation is displayed,
select [OK] or [CANCEL], and press
the <ENTER> button.
[HIGH ALTITUDE MODE]
Set to [ON] to use the projector at 1 400 m (4 593 ft)
to 2 700 m (8 858 ft) elevations.
1) Press ▲▼ to select [HIGH ALTITUDE
MODE].
2) Press ◀▶ to switch [HIGH ALTITUDE
MODE].
[OFF]
[ON]
[OFF]
When using at a place lower than
1 400 m (4 593 ft) above sea level
[ON]
When using at a high altitude
(1 400 m (4 593 ft) or higher and
lower than 2 700 m (8 858 ft) above
sea level)
3) When the confirmation is displayed,
select [OK] or [CANCEL], and press
the <ENTER> button.
Note
z
The speed of the fan increases and the operation
sound becomes louder when set to [ON].
z
The optional smoke cut filter cannot be used when
in high elevation mode.
[LAMP SELECT]
Select luminous lamps from the four equipped in the
projector body to turn on for a certain use condition or
purpose.
1) Press ▲▼ to select [LAMP SELECT].
2) Press ◀▶ to switch [LAMP SELECT].
2) Press ◀▶ to switch [LAMP SELECT].
▶
z
The setting will change as follows each time
you press the button.
[L1]
[L2]
[QUAD] (4 lit)
[L3]
[TRIPLE] (3 lit)
[L4]
[DUAL] (2 lit)
[L1/L4]
[SINGLE] (1 lit)
[L2/L3]
[L2/L3/L4]
[L1/L2/L3]
[L1/L3/L4]
[L1/L2/L4]
[L1]
Lamp 1 will light.
[L2]
Lamp 2 will light.
[L3]
Lamp 3 will light.
[L4]
Lamp 4 will light.
[L1/L4]
Lamp 1 and Lamp 4 will light.
[L2/L3]
Lamp 2 and Lamp 3 will light.
[L1/L2/L3]
Lamp 1, Lamp 2 and Lamp 3 will light.
[L1/L2/L4]
Lamp 1, Lamp 2 and Lamp 4 will light.
[L1/L3/L4]
Lamp 1, Lamp 3 and Lamp 4 will light.
[L2/L3/L4]
Lamp 2, Lamp 3 and Lamp 4 will light.
[SINGLE]
(1 lit)
One lamp will light. (A short usage
time lamp will automatically light.)
[DUAL]
(2 lit)
Two lamps will light. (A short usage
time lamp will automatically light.)
[TRIPLE]
(3 lit)
Three lamps will light. (A short usage
time lamp will automatically light.)
[QUAD]
(4 lit)
Four lamps will light.
3) Press the <ENTER> button.