LOEWE Individual 32 Compose 3D User Manual
- 20
english
Connecting the TV Set
Connecting to the mains
Remove the cover for the connections.
Connect the TV set to a 220-240V mains socket:
First plug the small plug of the power cable into the mains connection
on the back of the TV and then the large mains plug into a mains socket.
Remove the cover for the connections.
Connect the TV set to a 220-240V mains socket:
First plug the small plug of the power cable into the mains connection
on the back of the TV and then the large mains plug into a mains socket.
Connecting antennas
Cable (analogue) / DVB-C / DVB-T antenna:
Plug the antenna cable of antenna, cable system or room antenna into
the ANT TV socket.
If you want to use analogue cables / DVB-C connection and a DVB-T
antenna together, use an external antenna switch (available from your
dealer).
Cable (analogue) / DVB-C / DVB-T antenna:
Plug the antenna cable of antenna, cable system or room antenna into
the ANT TV socket.
If you want to use analogue cables / DVB-C connection and a DVB-T
antenna together, use an external antenna switch (available from your
dealer).
Satellite antenna DVB-S:
If the TV set is equipped with a Single or Twin satellite tuner (ex-factory or
means of upgrade kit / conversion kit), the ANT-SAT and ANT-SAT2 sockets
If the TV set is equipped with a Single or Twin satellite tuner (ex-factory or
means of upgrade kit / conversion kit), the ANT-SAT and ANT-SAT2 sockets
are available.
Depending on the used satellite system, connect a connecting cable from
Depending on the used satellite system, connect a connecting cable from
the multi-switch or directly from the LNC to the ANT-SAT and ANT-SAT2
sockets of the TV set respectively.
When connecting the TV set to a single cable community antenna, con-
When connecting the TV set to a single cable community antenna, con-
nect the ANT-SAT and ANT-SAT2 sockets directly to the appropriate SAT
antenna socket. Ask your dealer if required.
Installing the TV set
Installation options
Your TV set is delivered without installation options. This gives you the
option of choosing the installation solution tailored to your requirements
Your TV set is delivered without installation options. This gives you the
option of choosing the installation solution tailored to your requirements
from your Loewe dealer. Only use Loewe installation solutions (e.g. wall
mounts, floor stand) that are included in the Accessories – Setup pos-
sibilities chapter on page 143.
After selecting an installation option, read the appropriate assembly
instructions.
mounts, floor stand) that are included in the Accessories – Setup pos-
sibilities chapter on page 143.
After selecting an installation option, read the appropriate assembly
instructions.
Installation notes
Choose a place for installing your TV where no bright light or sunlight
shines directly onto the screen. This could cause reflections which impair
the picture.
3 times the screen diagonal can be taken as a guide value or the view-
Choose a place for installing your TV where no bright light or sunlight
shines directly onto the screen. This could cause reflections which impair
the picture.
3 times the screen diagonal can be taken as a guide value or the view-
ing distance (e.g. for 40-inch set approx. 3m for SD signal). The viewing
distance can be reduced with an HD signal.
distance can be reduced with an HD signal.
Set covers
Covers for rear and side connections
To remove the rear cable cover, pull the two recessed handles at the
bottom and drop down the cover.
To fit the cover, insert the lugs at the top edge of the cover into the corre-
sponding cut-outs in the rear panel and push up the cover until it snaps in.
The side cover of the TV set can also be completely removed. For this,
open it as far as it will go and gently pull on the open cover.
The cover detaches from the holder and gives free access to the con-
nection area. To replace the cover, simply push it until it latches back
into place.
To remove the rear cable cover, pull the two recessed handles at the
bottom and drop down the cover.
To fit the cover, insert the lugs at the top edge of the cover into the corre-
sponding cut-outs in the rear panel and push up the cover until it snaps in.
The side cover of the TV set can also be completely removed. For this,
open it as far as it will go and gently pull on the open cover.
The cover detaches from the holder and gives free access to the con-
nection area. To replace the cover, simply push it until it latches back
into place.
DVB-T
DVB-S
an. cable /
DVB-C
Initial installation
e.
R TV