Fostex FD-4 User Manual
Preview Function
70
1
1
2, 4
3
3
5
HOLD/> key
or
F FWD button
Time Base
ABS or MTC
BAR/BEAT/CLK
SF ->H ->M -> S ->F
SF <-H <- M <- S <- F
CLK -> BAR ->
CLK <- BAR <-
Flashing
EQ
EQ
ABS
LOC
S
M
H
F
SF
DRIVE
AUTO
A.PUNCH
SYNC OUT
CLK
SCSI
LOC
BAR
CLK
DRIVE
AUTO
A.PUNCH
SYNC OUT
CLK
SCSI
The FD-4 repeats playback of the “fall sound” at the locate point (edit
point). As shown in the diagram, one-second of data prior to the
locate point is played back, then muted (fade out) at the locate point.
The muted playback continues for one second. The FD-4 will repeat
this operation until you quit the Preview function.
point). As shown in the diagram, one-second of data prior to the
locate point is played back, then muted (fade out) at the locate point.
The muted playback continues for one second. The FD-4 will repeat
this operation until you quit the Preview function.
Quitting the Preview function
2. Press the STOP button or the EXIT/NO key.
Trimming the sound while previewing
You can trim the position of the locate point (edit point)
using the JOG dial while you preview the sound.
At this time, you can also adjust the size of the trimming
steps (the amount of offset controlled by the JOG dial).
Trimming allows you to fine-tune the position of the locate
point stored in the memory keys while previewing the sound.
Use this function to change the Auto Punch In/Out points,
the start point of Copy & Paste and Move & Paste, and the
start and end points of the Erase function.
using the JOG dial while you preview the sound.
At this time, you can also adjust the size of the trimming
steps (the amount of offset controlled by the JOG dial).
Trimming allows you to fine-tune the position of the locate
point stored in the memory keys while previewing the sound.
Use this function to change the Auto Punch In/Out points,
the start point of Copy & Paste and Move & Paste, and the
start and end points of the Erase function.
<Notes>
• You can audition the result of trimming during the next preview.
That is, if you trim the position while previewing the sound for the
first time, you can check the result when you preview the sound
next time.
• If the locate point is shifted outside the range of the preview
playback as a result of trimming, [Void Data!] and the locate
point indication appear alternately. In this case, you cannot use
the Preview function. Trim the position again so that it will be
within the playback range.
• When Auto Punch mode is turned on and you trim the Auto
Punch In or Auto Punch Out point while previewing the sound
with [Void Data!] indicated on the display, Auto Punch mode will
be cancelled.
1. Start previewing the sound by following the steps described
on the previous page.
2. Use the JOG dial to trim the position.
When previewing starts, the unit of JOG trimming flashes
on the screen. For example, SF (sub-frame) flashes if ABS
Time Base or MTC Time Base is selected. CLK (clock)
flashes if BAR/BEAT/CLK is selected.
The flashing value also indicates the position you can
trim.
on the screen. For example, SF (sub-frame) flashes if ABS
Time Base or MTC Time Base is selected. CLK (clock)
flashes if BAR/BEAT/CLK is selected.
The flashing value also indicates the position you can
trim.
(Example) Time Base is ABS: (SF flashes.)
(Example) Time Base is BAR/BEAT/CLK (CLK flashes.)
Flashing
3. To change the unit of trimming, press the HOLD/> key, the
REWIND button, or the F FWD button.
These buttons will change the trimming unit as follows:
4. Trim the position at the selected unit (digit).
Quitting the trimming function
5. Press the STOP button or the EXIT/NO key.
The trimmed locate point (edit point) data will be stored
in the corresponding memory key.
in the corresponding memory key.
REWIND
button
5