Fostex FD-4 User Manual
81
Changing the Initial setting (SETUP mode)
Sign. Set ? menu
Tempo Set ? menu
Title Edit ? menu
Del PGM ? menu
Click ? menu
Preroll ? menu
Sync Out? menu
Frame Rate ? menu
Mtc Offset ? menu
Ofset Mode ? menu
Slave Mode? menu
Slave Type? menu
Rec Protect ? menu
Digi. in ? menu
Digi. out ? menu
Resolu ? menu
Device ID ? menu
Load PGM ? menu
Save PGM ? menu
Format ? menu
SETUP
DRIVE
AUTO
A.PUNCH
SYNC OUT
CLK
SCSI
SETUP mode of the FD-4 offers the “Changing the initial
settings” menus that configure the operating environment
of the FD-4, and the “Execution” menus that execute cer-
tain operations, such as save and load.
The “Changing the initial settings” menus include 16 pa-
rameters as shown in Table-1 below. These parameters were
set before the unit was shipped from the factory (These
values are called “initial settings.”). Modifying these set-
tings allows you to change the operating environment of
the FD-4.
Also, as shown in Table-2, the “Execution” menus include
five items: Title Edit?, Del. PGM?, Load PGM?, Save PGM?,
and Format?, which you can execute by selecting the corre-
sponding SETUP menu. This chapter explains how to use
the “Changing the initial settings” menus shown in Table-
1. For more information on the “Execution” menus, refer to
the corresponding pages in the “Reference page” column
in Table-2.
settings” menus that configure the operating environment
of the FD-4, and the “Execution” menus that execute cer-
tain operations, such as save and load.
The “Changing the initial settings” menus include 16 pa-
rameters as shown in Table-1 below. These parameters were
set before the unit was shipped from the factory (These
values are called “initial settings.”). Modifying these set-
tings allows you to change the operating environment of
the FD-4.
Also, as shown in Table-2, the “Execution” menus include
five items: Title Edit?, Del. PGM?, Load PGM?, Save PGM?,
and Format?, which you can execute by selecting the corre-
sponding SETUP menu. This chapter explains how to use
the “Changing the initial settings” menus shown in Table-
1. For more information on the “Execution” menus, refer to
the corresponding pages in the “Reference page” column
in Table-2.
<Table-1> “Changing the initial settings” menus
Parameters
Default setting
Refer page
“Setting a time signature”
001 BAR 4/4
82
“Setting a tempo”
001 BAR1 120
83
“Setting the Metronome function”
OFF
85
“Setting a preroll value”
00
85
“Setting MIDI sync output signal”
CLK (Clock)
86
“Setting an MTC frame rate”
25 frame
87
“Setting an MTC offset value”
00h59m57s00f00sf
87
“Setting Offset mode”
ABS
88
“Setting the Slave mode”
OFF
88
“Setting the Slave type”
Vari
89
“Setting the Record Protect function”
OFF
90
“Setting digital input tracks”
L-, r- (no assign)
91
“Setting digital output tracks”
L- , r- (
ST OUT)
92
“Setting BAR/BEAT resolution mode” OFF
92
“Setting the MIDI device number”
00
93
<Table-2> “Execution” menu
Items
Refer page
Editing a Program title
38
Deleting a Program
39
Saving song data to an external DAT
77
Loading song data from an external DAT
79
Formatting an external SCSI disk
6-8
Selecting SETUP mode
Follow the steps below to select the desired SETUP menu in
SETUP mode.
SETUP mode.
1. While the FD-4 is stopped, press the SETUP key on the
control panel.
Pressing the SETUP key causes the FD-4 to enter SETUP
mode. The FD-4 displays the first hierarchy level of the
SETUP menu you selected before you turned off the power.
At this time, the menu graphics appear as shown below.
The flashing menu indicator is the currently-selected
menu. Turning the JOG dial will select a different menu
and the corresponding menu indicator will flash.
The following diagram shows the position of each menu.
mode. The FD-4 displays the first hierarchy level of the
SETUP menu you selected before you turned off the power.
At this time, the menu graphics appear as shown below.
The flashing menu indicator is the currently-selected
menu. Turning the JOG dial will select a different menu
and the corresponding menu indicator will flash.
The following diagram shows the position of each menu.
Changing the Initial Settings
(SETUP Mode)
<Note>
With the factory initial settings, or when you turn on the power again after
you format an external SCSI disk, “Sign. Set? (Setting a time signature)”
appears. Otherwise, the first hierarchy level of the previously-selected
SETUP menu appears.
you format an external SCSI disk, “Sign. Set? (Setting a time signature)”
appears. Otherwise, the first hierarchy level of the previously-selected
SETUP menu appears.
The title of the SETUP menu ap-
pears. You can select a different
menu via the JOG dial.
pears. You can select a different
menu via the JOG dial.
This lights up when the FD-4
enters SETUP mode.
enters SETUP mode.
This indicates the position of the SETUP menu. Selecting a menu
via the JOG dial will move the flashing cursor.
via the JOG dial will move the flashing cursor.
2. Select the desired menu using the JOG dial, then press the
EXECUTE/YES key.
The FD-4 displays the second hierarchy level of the
selected SETUP menu, where you can set parameters.
(Refer to the next page for more information.)
selected SETUP menu, where you can set parameters.
(Refer to the next page for more information.)
To exit SETUP mode, press the STOP button or the EXIT/NO key. Each
time you press one of these keys, the FD-4 returns to the previous hier-
archy level of the menu, and finally exits SETUP mode.
time you press one of these keys, the FD-4 returns to the previous hier-
archy level of the menu, and finally exits SETUP mode.