Kenwood TK-980 Leaflet
ADS#44307 Printed in USA
JQA-QMA1205
■
KMC-9C
Control Station
Desktop Microphone
Desktop Microphone
■
KMC-27A
Microphone
(MIL-SPEC Noise-Canceling)
(MIL-SPEC Noise-Canceling)
■
KMC-27B
Microphone
■
KMC-28A
Keypad Microphone
(MIL-SPEC Noise-Canceling)
(MIL-SPEC Noise-Canceling)
■
KCT-18
Ignition Sense Cable
■
KCT-19
Accessories Connector
Cable
Cable
■
KCT-31
PC Serial Interface
Cable
Cable
■
KES-3
External Speaker
■
KES-5
External Speaker
■
KMB-2B
Mounting Case
■
KMB-10
Key Lock Adapter
■
KMB-20
Mounting Case
■
KPS-15
DC Power Supply
■
KLF-2
Line Noise Filter
■
KAP-1
PA/HA Unit
■
KDS-100
Mobile Data Terminal
■ KGP-2A/2B
GPS Receiver /
Modem Unit
Modem Unit
All accessories and options may not be available in all markets.
Contact an authorized Kenwood dealer for details and complete list of all accessories and options.
Contact an authorized Kenwood dealer for details and complete list of all accessories and options.
Options
Specifications
footnotes from Front:
1
Trunked Format: 32 Systems max. (prog. for LTR
®
or Conventional),
250 Groups per system max (limited per repeater channels
programmed).
programmed).
2
DTMF Encode includes PTT ID, Emergency ANI, Manual Encode
(KMC-28A DTMF mic required), Auto-Dial (32 numbers); DTMF
Decode includes Stun (dead beat disable), primary/secondary
selective call with call alert and transpond.
(KMC-28A DTMF mic required), Auto-Dial (32 numbers); DTMF
Decode includes Stun (dead beat disable), primary/secondary
selective call with call alert and transpond.
3
Ignition sense requires KCT-34 ACC cable & KCT-18 Ignition
sense cable options.
sense cable options.
4
Public Address / Horn Alert Option- requires KAP-1 PA/HA Unit and
KCT-34 ACC Cable options.
KCT-34 ACC Cable options.
5
KPG-49D required: Windows
®
98/ NT/ 2000/ Me/XP compatible.
6
Kenwood LTR
®
Features: KPG-49D Group Delete/Add, LTR
®
Talk
Around, Scan Revert Group Display, System Scan, Group Scan,
Auto Search.
Auto Search.
7
FleetSync
®
(not FleetSync
®
II capable)
8
Short Text Messages are radio stored & LCD displayed.
Model
TK-980
TK-981
GENERAL
Frequency Range
Type 1 (RX)
Type 1 (RX)
851~870 MHz
935 ~ 941 MHz
Type 2 (TX)
806 ~ 825 MHz,
896 ~ 902 MHz,
Type 3 (Talk Around)
851 ~ 870 MHz
935 ~ 941 MHz
Systems
Max. 32
Group
Max. 250 per system
Channels
LTR
LTR
®
Mode
Max. 600
(Conventional)
Max. 250
PLL Channel Spacing
25 kHz
12.5 kHz
(PLL step: 12.5 kHz)
Operating Voltage
13.6 V DC ± 15 %
Current Drain
Standby
Less than 0.4 A
Receive
Less than 1.0 A
Transmit
Less than 7.0 A
Duty Cycle
Transmit: 20%
Operating Temperature
-22° F ~ +140° F
Range
(-30° C ~ +60° C)
Frequency Stability
±0.00015%
(-22° F ~ +140° F)
Antenna Impedance
50
Ω
Dimensions (W x H x D)
5-1/2 x 1-1/2 x 5-3/4 in. (140 x 40 x 145 mm)
Weight (net)
2.07 lbs. (940 g)
FCC ID
ALH24563110
ALH24572110
IC Certification
282195546A
282195545A
Model
TK-980
TK-981
RECEIVER
(Measurements made per TIA/EIA-603)
Sensitivity (12 dB SINAD)
0.25 µV
Selectivity*
75 dB
68 dB
Intermodulation Distortion
70 dB
65 dB
Spurious Response*
80 dB
Audio Output
4 W with less than 5% distortion
Channel frequency spread
19 MHz
6 MHz
TRANSMITTER
(Measurements made per TIA/EIA-603)
RF Power Output
15 W
Spurious & Harmonics
60 dB
Modulation
16KØF3E
11KØF3E
FM Noise
45 dB
40 dB
Audio Distortion Less than 3%
Less than 5%
Microphone Impedance
Low Impedance
Channel Frequency Spread
64 MHz
45 MHz
FleetSync
®
is a registered trademark of Kenwood Corporation.
LTR
®
is a registered trademark of Transcrypt International.
* Typical specifications
Kenwood follows a policy of continuous advancement in development.
For this reason specifications may be changed without notice.
Kenwood follows a policy of continuous advancement in development.
For this reason specifications may be changed without notice.
GPS-2A
GPS-2B
Applicable MIL-STD
Standard
MIL 810C
MIL 810D
MIL 810E
MIL 810F
Methods/Procedures
Methods/Procedures
Methods/Procedures
Methods/Procedures
Low Pressure
500.1/Procedure I
500.2/Procedure I, II
500.3/Procedure I, II
500.4/Procedure I, II
High Temperature
501.1/Procedure I, II
501.2/Procedure I, II
501.3/Procedure I, II
501.4/Procedure I, II
Low Temperature
502.1/Procedure I
502.2/Procedure I, II
502.3/Procedure I, II
502.4/Procedure I, II
Temperature Shock
503.1/Procedure I
503.2/Procedure I
503.3/Procedure I
503.4/Procedure I, II
Solar Radiation
505.1/Procedure I
505.2/Procedure I
505.3/Procedure I
505.4/Procedure I
Humidity
507.1/Procedure I, II
507.2/Procedure II, III
507.3/Procedure II, III
507.4
Sand & Dust
510.1/Procedure I
510.2/Procedure I
510.3/Procedure I
510.4/Procedure I, III
Vibration
514.2/Procedure VIII, X
514.3/Procedure I
514.4/Procedure I
514.5/Procedure I
Shock
516.2/Procedure I, II, III, V
516.3/Procedure I, IV, V
516.4/Procedure I, IV, V
516.5/Procedure I, IV, V