Transition Networks SGETF1017-100 User Manual
SGETF10xx IN THE NETWORK
Install two SGETF10xx series media converters in series to extend, over fiber,
the distance between two 1000BASE-TX devices.
the distance between two 1000BASE-TX devices.
Use one SGETF10xx media converter to connect a 1000BASE-TX terminal
device and a 1000BASE-SX/LX hub, switch, or router.
device and a 1000BASE-SX/LX hub, switch, or router.
NOTE: A TRANSITION Networks stand-alone media converter can be installed
in series with a TRANSITION Networks chassis media converter that has a
related model number, such as an SGETF10xx with a CGETF10xx.
in series with a TRANSITION Networks chassis media converter that has a
related model number, such as an SGETF10xx with a CGETF10xx.
INSTALLATION
Set 4-Position Switch
Use small flatblade screwdriver or similar device to set recessed switches.
Refer to drawing for four-position switch locations.
Refer to drawing for four-position switch locations.
Full/Half-Duplex Advertisement (UP=Enabled) Allows full-duplex mode.
(DOWN) Allows half-duplex mode.
(DOWN) Allows half-duplex mode.
Pause Advertisement (UP=Enabled)
Allows auto-negotiation pause. (DOWN)
Allows NO auto-negotiation pause.
Allows auto-negotiation pause. (DOWN)
Allows NO auto-negotiation pause.
NOTE: If the Pause feature is present on
all network devices attached to the media
converter(s), enable Pause on the media
converter(s). Otherwise, disable Pause on the media converter(s).
all network devices attached to the media
converter(s), enable Pause on the media
converter(s). Otherwise, disable Pause on the media converter(s).
LPT (UP=Enabled) Allows a fault EITHER on the copper OR on the fiber side
of the media coverter to stop signal and data transmission on the other side.
(DOWN) Disables LPT.
of the media coverter to stop signal and data transmission on the other side.
(DOWN) Disables LPT.
TECHNICAL SPECIFICATIONS
Standards
IEEE 802.3ab, IEEE 802.3 1998
Data Rate
1000 Mb/s
Dimensions
3.4" x 0.86" x 5.0" (86mm x 22mm x 127mm)
Weight
8 oz (approximate)
Delay
300 nsec
Power Consumption
6.5 Watts
Power Supply Requirements Replace power supply with only the equivalent
input rating (see below) and output rating (unregulated 9-24VDC, 5.5W).
input rating (see below) and output rating (unregulated 9-24VDC, 5.5W).
TN PN
Requirement
Location
12 V, 1.5 A
3507
3507
240 volts, 50 hertz
United Kingdom
3342
230 volts, 50 hertz
Europe
3340
120 volts, 60 hertz
USA/Canada/Mexico
3346
100 volts, 50-60 hertz
Japan
3511
240 volts, 50 hertz
Australia
3537
IEC320 (with power cord: 3522)
South Africa
9 V, 1 A
25039
25039
IEC320, 90-250VAC input
NOTE: Requires
appropriate IEC320
power cord for location
appropriate IEC320
power cord for location
25040
120 volts, 60 hertz
USA/Canada/Mexico
Environment
Typical Operating Temperature*: 0°
to
50°C (32°
to
122°F )
Storage Temperature:
-20°
to
85°C (-4°
to
185°F)
Humidity
10-90%, non condensing
Altitude
0-10,000 feet
Warranty
Lifetime
DECLARATION OF CONFORMITY
Name of Mfg:
Transition Networks
6475 City West Parkway, Minneapolis MN 55344 USA
6475 City West Parkway, Minneapolis MN 55344 USA
Model:
SGETF10xx-100 Series Media Converters
Part Number(s):
SGETF1013-100, SGETF1014-100, SGETF1015-100,
SGETF1017-100
SGETF1017-100
Regulation:
EMC Directive 89/336/EEC
Purpose: To declare that the SGETF10xx-100 to which this declaration refers is
in conformity with the following standards.
EMC-CISPR 22: 1985 Class A&B; EN 55022: 1988 Class A&B; EN 50082-1:1992;
EN 60950 A4:1997; IEC 801.2, IEC 801.3, and IEC 801.4; IEC 950
EN 60950 A4:1997; IEC 801.2, IEC 801.3, and IEC 801.4; IEC 950
I, the undersigned, hereby declare that the equipment specified above conforms to the
above Directive(s) and Standard(s).
_ January 6, 2001_____
Stephen Anderson, Vice-President of Engineering
Date
Not Used
LPT UP=ON
Pause Advertisement UP=ON
Full/Half-Duplex Advertisement UP=ON