User ManualTable of ContentsContents4About This Reference9Finding Specific Information in This Reference9Conventions10Contacting 3Com10Overview11Supported Features11Accessing the User Interface11Dual T1/PRI Configuration13Configuring Span Lines 1 and 213Menu Option 114Configuring the span line’s framing mode14Menu Option 214Configuring the span line’s line coding14Menu Option 314Responding to a span line remote (framer) loopback14Menu Option 415Configuring the span line’s jitter attenuation15Menu Option 515Configuring the span line’s transmit line build out15Menu Option 616Configuring for the Telco’s switch type16Menu Option 716Configuring the span line’s idle bit pattern16Menu Option 817Mapping the span line’s DS0s to chassis modems17Menu Option 918Configuring the span line’s signaling channel18Menu Option 1018Configuring the span line’s interface ID18Menu Option 1118Configuring span level call-type blocking18Menu Option 1218Configuring span level cause codes18Menu Option 1319Configuring the DS0 level call-type blocking19Menu Option 1420Configuring the DS0 level service state20Menu Option 1520Configuring the Short Haul NIC line length20Menu Option 1621Allowing for ALERTING message in response to SETUP request21Configuring Inbound Call Routing22Menu Option 122Selecting a Gateway to process digital calls22Menu Option 222Allowing modem analog calls22Menu Option 323Configuring inbound call routing23Menu Options 4 and 523Checking the inbound call routing configuration status23Menu Option 624Mapping inbound phone numbers to reserved pools24Menu Option 725Mapping chassis modem channels to reserved pools25Menu Option 825Mapping digital reserved pools to chassis Gateways25Menu Option 926Allowing ISDN-GWC termination26Configuring the Card26Menu Option 126Saving configuration changes to NVRAM26Menu Option 227Restoring configuration from NVRAM27Menu Option 327Restoring the default configuration27Menu Option 427Assigning timing source priority27Menu Option 527Configuring chassis slot devices27Menu Option 628Configuring the modem routing method28Menu Option 728Configuring the UI console password28Menu Option 828Enabling automatic DS0 state change28Menu Option 929Companding Code Configuration29Configuring Software Fault Event Logging29Dual T1/PRI Maintenance30Dual T1/PRI Commands30Menu Option 131Resetting the highest priority timing source31Menu Option 231Resetting the PRI NAC31Menu Option 331Enter/Exit span-to-span pass-thru loopback mode31Menu Options 4 and 632Forcing receiver reframe on the span lines32Menu Options 5 and 732Disconnecting calls on specific span line B-channels32Menu Option 832Forcing the NAC to master the TDM bus32Menu Options 9 and 1032Entering and exiting locally initiated loopbacks on the span lines32Menu Option 1133Disabling red ALARM LEDs33Menu Options 12 and 1333Connect/disconnect B-channel on span lines 1 and 233Menu Options 14 and 1533Changing individual DS0 service states33Menu Options 16 and 1733Changing span line service state33Logging Out of the UI Console34Dual T1/PRI Status Displays35Dual T1/PRI Status Displays35Menu Option 136Checking power-up self test status36Menu Option 237Checking the T1/PRI’s overall status37Menu Option 337Checking chassis slot device configurations37Menu Option 438Checking DS0/modem channel status38Menu Option 538Checking the chassis’ ISDN gateway status38Menu Options 6 and 839Checking span line 1 and 2’s DS0 status39Menu Options 7 and 940Checking span line 1 and 2’s alarm/event status40Trouble Clearing44Using the LEDs44About T1/PRI Alarm Levels45Correcting Alarm/Error Conditions46Using SNMP Traps47Technical Specifications48Certification48Regulatory Compliance Statements48United States48FCC Part 15 Compliance Statement48Current Draw48Environment49Shipping and Storage49Operating49Physical Dimensions49Index50Size: 650 KBPages: 52Language: EnglishOpen manual