User ManualTable of ContentsAccelePort T1 Modem Bank Overview1Unpacking2Planning the T1 WAN Interface3Connections to the WAN3Carrier Approval3CSU Mode3Line Build Out4CSU Specification4T1 Cable Specification4Parameters Specified to the Carrier5Planning Worksheets6General Information6Hardware Installation8T1 Modem Bank Power Supply Installation/Replacement8T1 Modem Bank Standalone or Rack Installation10Standalone Installation Procedure11Requirements for Rack Installations12Mounting Bracket Installation for a 24-inch Rack12General Rack Installation Directions14Daisy Chaining T1 Modem Bank Units16Daisy Chain Example17Connecting a Modem18Daisy Chaining T1 Modem Bank Units and EPC/CON-16 Concentrators19Fault Tolerance19EPC/X Host Adapter Installation20PCI Host Adapters20Configuring the Host Adapter20Installing the PCI Host Adapter in your Computer20ISA Host Adapters21Setting the I/O Port Address21Factory-Set Jumper J122Installing the ISA Host Adapter in your Computer22EISA Host Adapters23Factory-Set Jumpers23Installing the EISA Host Adapter in your Computer23System Configuration23Connecting the EPC/X Host Adapter to the T1 Modem Banks25Software Installation and Configuration27Setting the Node Number27Installing Download29POST Failure30Possible Problem31Restarting POST31Display Panel Status Indicators31Software Installation for Novell Systems34Introduction34Installing the EPC/X AIO Device Driver35Installing the AIO Application35Installing SNMP35Installing QuickManager35Configuring the T1 Modem Banks36Software Installation for Windows NT Systems38Installing the EPC/X Windows NT Device Driver38Installing the Windows NT SNMP Service38Windows NT 3.5138Windows NT 4.039Installing RAS39Installing the Management Software39Host System Installation39Remote System Installation40T1 Modem Bank Configuration41Configuring via QuickManager41Configuring via the Terminal Port44Configuring via the Display Panel45Configuring via the Serial Port Interface47Configuration modification49Equipment List51System Information52Modem Switchhook Status53Alarm Status54T1 Modem Bank Diagnostics56Running Diagnostics with QuickManager57Running Diagnostics from the Display Panel58Running Diagnostics from the Terminal Port59Diagnostic Test Descriptions62Test 1: Front Panel Test62Test 2: RAM Test62Test 3: Timer Test62Test 4: Line Card Test63Test 5: Modem Test63Test 6: Sync Internal Loopback Test63Test 7: Sync External Loopback Test64Test 8: EEPROM Test64Test 9: Watchdog Test64Component Removal and Installation65Line Card Removal and Replacement66Modem Card Removal and Installation/Replacement68Modem Card Removal68Modem Card Installation/Replacement71Power Supply Removal73Fan Assembly Removal and Replacement75Fuse Replacement76Connections to the Telephone Network77Alarms on a T1 Span78T1 Modem Bank Interaction78Physical Specifications79T1 Modem Bank Power Cord Specifications79T1 Modem Bank Environmental Requirements80T1 Modem Bank Rack Specifications80Standalone Unit Specifications80Rack Specifications804U 19 Inch Rack System804U 24 Inch Rack System80Daisy Chain Cables81Terminator Plug81T1 Loop Back Plug81T1 Modem Bank Certification82Glossary83Appendix A — Memory Conflicts85Contention for Memory Addresses85ISA Host Adapters87Conflicts Between 8-Bit and 16-bit Memory Devices87EISA Host Adapters88Appendix B — Transmission Modes89Appendix C — Terminal Port Cable91Appendix D — Specifications and Wiring Pin Diagrams92Line Card Connector92Connector for Sync Channels93Terminal Port93Appendix E — Generic T1 Modem Bank Wiring Modes94Eight-Wire Direct Wiring94Four-Wire Direct Wiring95Restrictions on Daisy Chain Cable Lengths96Eight-Wire Synchronous Modem Wiring97Appendix F — Modem AT Command Set99Basic AT Commands99AT& (Ampersand) Commands105AT% (Percent) Commands111AT\ (Backslash) Commands112AT- (Dash) Commands116AT" (Quote) Commands117Class 1 FAX Commands118Class 2 FAX Commands120Class 2 FAX Responses127S Registers128S Register Definitions129Result Codes143Display Format Options143Extended Message Options144Negotiation Progress Messages146Index149T1 Modem Bank Chassis, Front View1Power Supply9Line Card and Synchronous Cable Connections for Standalone T1 Modem Bank11Bracket Position For 19-inch Rack12Bracket Position For 24-inch Rack13T1 Modem Bank Unit Spacer14Line Card15Synchronous Ports and Terminal Port16Two Daisy Chains of T1 Modem Banks to be Connected Locally17Remote T1 Modem Bank Units18Mixing EPC Concentrators with T1 Modem Bank Units19DIP Switch Settings for I/O Port Address21EPC/X Host Adapter Connected Locally to T1 Modem Banks25Local and Remote T1 Modem Bank Units26EPC/X Host Adapter Connected to Concentrators and T1 Modem Bank Units26T1 Modem Bank Display Panel28Main Screen36T1 Modem Bank Configuration Screen37Line Card Status Display42Line Card Options Display43Modem Test Results57Line Card66Modem Card69Quick Manager Modem Revision Screen71Power Supply74Fan Assembly75AC Power Inlet76T1 Modem Bank and Public Switched Telephone Network77Functional Block Diagram of the T1 Modem Bank78Typical PC Memory Usage - 1st Megabyte86Simple Terminal Cable91RJ-45 Plug92Eight-Wire Direct Daisy Chain Cable Wiring94Four-Wire Direct Daisy Chain Cable Wiring95RS-232 Synchronous Modem Cables97RS-422 Synchronous Modem Cables98T1 Modem Bank Shipping Carton Contents2CSU Technical Description4Requirements for T1 Modem Bank Setup6Error Message Codes30Display Panel Status Codes32Component Level Troubleshooting65Types of Modem Cards70Daisy Chain Cable Length vs. Baud Rate96Supported FAX Transmit/Receive Modulations119Node number1Size: 2.9 MBPages: 160Language: EnglishOpen manual