User ManualTable of ContentsTABLE OF CONTENT 10.3.07.doc2TABLE OF CONTENTS2PAGE 1-2 10.3.07.doc3PAGE 3 10.3.07.doc5PAGE 4 10.3.07.doc6PAGE 5 10.3.07.doc7LOCATION7PAGE 6 10.3.07.doc8PAGE 7 10.3.07.doc9SIDE SHELF HANDLE ASSEMBLY9BATTERY INSTALLATION91. Remove the ignition button housing.92. Insert the battery into the housing with the positive (+) terminal facing outward.93. Replace the ignition button housing after the battery has been installed.9PAGE 8 10.3.07.doc10BRAKING SYSTEM OPERATIONS10LIQUID PROPANE CYLINDER RETENTION SYSTEM10PAGE 9 10.3.07.doc11PAGE 10-12 10.3.07.doc12LIQUID PROPANE CYLINDER REQUIREMENTS12(20 lb. Cylinder)12GENERAL13It is handy to keep a spray bottle of soapy water near the shut-off valve of the gas supply line. Spray all the fittings. Bubbles indicate leaks.13Disconnected liquid propane cylinders must have threaded valve plugs tightly installed, and must not be stored in a building, garage or any other enclosed area.13The gas must be turned off at the supply cylinder when the unit is not in use.14If the appliance is stored indoors, the cylinder must be disconnected and removed from the appliance.14Cylinders must be stored outdoors in a well-ventilated area out of the reach of children.14PAGE 13-14 10.3.07.doc15WARNING15The rotisserie motor is equipped with a plug and should be plugged directly into a properly grounded receptacle in accordance with local codes or, in the absence of local codes, with the National Electrical Code, ANSI/NFPA 70, or the Canadian Electrical Code, CSA C22.1. DO NOT cut or remove the grounding prong from this plug.15Keep the rotisserie motor cord away from the heated surfaces of the grill. When not in use remove and store the motor in a dry location.15PAGE 15 10.3.07.doc17PAGE 16-18 10.3.07.doc18TO MATCH LIGHT THE GRILL18Page 19 10.3.07.doc21Page 20 10.3.07.doc22PAGE 21-22 10.3.07.doc23LIGHTING INSTRUCTIONS23MATCH LIGHTING23STAINLESS STEEL24GRILL RACK24GRILL BURNERS24WARNING24Failure to properly place the burner over the orifice could cause a fire to occur behind and beneath the valve panel, thereby damaging the grill and making it unsafe to operate.24GRILL BURNER REMOVAL/INSTALLATION24The grill burners are factory installed.24To remove the main burners for cleaning:241. Locate the nut at the rear of the burner on the bottom side.242. Remove the nut and lift the burner out of the fire box.24To reinstall the main burners:243. Insert the burner over the valve assembly (Item# 20 on page 24).244. Insert the back of the burner into the hole at the rear of the fire box and reinstall the nut.245. Make sure orifice spud is inside the burner’s venturi as shown below.24PAGE 23 10.3.07.doc25PAGE 27-29 10.3.07.doc29WARNING29PAGE 30-31 10.3.07.doc32BBQ SALMON32Preheat the BBQ32BAKED CHILI CORN32TANGY SEAFOOD KABOBS32PORK CHOPS32BARBECUED LONDON BROIL32VEGETABLE KABOBS32FAJITAS32BEEF AND LAMB KABOBS33EGGPLANT CAVIAR33CHICKEN TANDOORI STYLE33SPARE RIBS33PORK ROAST33TURKEY33PAGE 32 10.3.07.doc34LIMITED WARRANTY34MODEL #720-051134STAINLESS STEEL OUTDOOR GAS GRILL34Size: 2.51 MBPages: 34Language: EnglishOpen manual
