User Manual
Table of Contents
- Body - For important information on any of these LifeScan products, refer to the appropriate oper...14
- 16
- Body - A configuration option may be set to maintain your ID for up to 1 hour after the bedside u...19
- Body - To scan a barcode, hold the barcode label parallel to and approximately 6 to 10 inches fro...20
- Body - This product contains a laser. Do not stare into the laser light or point it towards anyon...20
- Body - Confirmation Dot is read by the bedside unit to determine the sample’s glucose concentrati...22
- 28
- Body - Use SureStepPro Glucose Control Solutions with the SureStepPro Bedside Unit and SureStepPr...29
- 31
- 32
- 32
- Body - A configuration option may have been selected which would allow you to enter a new test st...33
- Body - The QC Test screen appears with messages prompting you to apply the control to the test st...34
- Body - If you fail to completely insert the test strip, the test may start; however, you may rece...36
- Body - You have up to 2 minutes to insert the test strip after the control solution is applied. I...36
- Body - Depending on the configuration option setting, the QC result will be displayed as either a...37
- Body - The comments that appear at the Select Comment screen have been selected by your system ad...38
- 43
- 43
- Body - If your operator ID is required, a configuration option may be set to remember your ID for...43
- Body - A configuration option may have been selected which would allow you to enter a new test st...44
- Body - The Patient Test screen appears with messages prompting you to apply blood to the strip an...45
- Body - Obtain a drop of blood. Capillary blood can be obtained from puncturing the finger or heel...45
- Body - Carefully touch the center of the pink test square to the drop of blood on the patient’s f...46
- Body - Touch the tip of the syringe to the center of the pink test square. Gently apply pressure ...47
- Body - Alternatively, dispense the blood from the syringe into a test tube, then apply blood to t...47
- Body - Touch the drop of blood emerging from the tip of a narrow-bore pipette to the center of th...47
- Body - If white patches or streaks continue to appear after you have repeated the test with a new...49
- Body - If you fail to completely insert the test strip, the test may start; however, you may rece...49
- Body - A glucose range may have been defined by your system administrator. Results that fall abov...50
- 52
- Body - The comments that appear at the Select Comment screen have been selected by your system ad...52
- Body - A series of messages are displayed on the bedside unit screen indicating the status of the...56
- Body - The connection module, used with a modem, provides a remote communication link between the...56
- Body - If a fax machine is sharing the same analog line as the connection module modem, do not tr...56
- Body - SureStepPro 2.0 users – If you are transferring data over an Ethernet network, MeterLink s...56
- Body - Messages appear on the screen indicating the status of the connection. The indicator light...58
- 59
- Body - When the bedside unit memory is full, a message appears informing you that there is no roo...61
- Body - You may review patient, QC, linearity, and unknown solution test results. In-Service test ...61
- Body - Clean the outside of the unit with a cloth moistened with a 10% bleach solution. Follow wi...66
- Body - Clean the test strip holder (cover and base), lens area, and contact points. Use a 10% ble...66
- Body - Do not use alcohol, glass cleaners, or any cleansers containing abrasives, phenol, or ammo...66
- Body - The SureStepPro Bedside Unit is powered by two size C alkaline batteries. Change the batte...69
- Body - Neither the LOW BATTERY message nor the removal of batteries affects the test results stor...69
- 74
- 75
- 75
- 76
- Body - If you fail to completely insert the test strip, the test may start; however, you may rece...79
- Body - You have up to 2 minutes to insert the test strip after the linearity solution is applied....79
- 82
- 83
- Body - If you fail to completely insert the test strip, the test may start; however, you may rece...86
- Body - You have up to 2 minutes to insert the test strip after the solution is applied. If you in...86
- 108
- 110
- 112
- 117