User ManualTable of ContentsDIGITAL VNswitch 900GV1Installation and Configuration1Contents3Preface3Overview vii3Safety3Overview xv31 Product Introduction3Overview 1-132 Installing the DIGITAL VNswitch 900GV4Overview 2-143 Installing the Setup Port Cable4Overview 3-144 Configuring the Module in a DIGITAL MultiSwitch 9004Overview 4-145 Removing the Cables, Connector and Module5Overview 5-15A Problem Solving5Overview A-15B Connectors and Adapters5Overview B-15C Product Specifications5Overview C-15Preface7Overview7Purpose of the Manual7Intended Audience7Organization8Associated Documents9Conventions10Accessing Online Information11Documentation Comments11Online Services11Safety13Overview13Chapter 115Product Introduction15Overview15In This Chapter15What is the DIGITAL VNswitch 900GV?16Features17Hot Swap17Configuration and Management17Bridging18Ethernet18SNMP18MIBS19RMON19VLAN Secure Domains20Chapter 221Installing the DIGITAL VNswitch 900GV21Overview21Introduction21In This Chapter21Module Components22Front Panel Components22Figure 2-1: Front Panel LEDs and Connectors22Table 2-1: Front Panel LEDs and Connectors22Back Panel Components24Figure 2-2: Back Panel Components24Table 2-2: Back Panel Components24How to Install the Module25Task 1: Compare the Power Ratings25Figure 2-3: Sample Power Ratings25Task 2: Seat the Module26Figure 2-4: Seating the Module26Task 3: Verify Initial LED Operation27Task 4: Connect the LDM Port Cable28Figure 2-5: LDM Port Cable Connection28Task 5: Connect the GBIC Connector29Figure 2-6: GBIC Connection29Task 6: Connect the Duplex SC Cables30Warning30Table 2-3: Short Wave Length - Black (HP 5601 - 850)30Table 2-4: Long Wave Length - Blue (HP 5611 - 1300)30Chapter 331Installing the Setup Port Cable31Overview31Introduction31In This Chapter31Setup Port Signaling Standards32Setup Port Device Cabling32Connecting to the Setup Port33Figure 3-1: Setup Port Cabling Components34Chapter 435Configuring the Module in a DIGITAL MultiSwitch 90035Overview35Introduction35In This Chapter35Assigning an IP Address36NOTE36DIGITAL MultiSwitch 900 INSTALLATION MENU37[9] Start Redirect Mode38NOTE38Using Menus to Configure the Module39[1] Restart with Factory Defaults40CAUTION40[2] Restart with Current Settings41NOTE41[3] Show Current Settings42[4] Configure IP43NOTE43[1] Set SNMP Read/Write Community45[2] Add SNMP Trap Addresses46[3] Delete SNMP Trap Addresses47[4] Set In-Band Interface IP Address48NOTE48[5] Set Out-of-Band Interface IP Address49[6] Set Default Gateway50[5] Go to Local Console51[6] Product-Specific Options (VNswitch 900GV)52[10] Product-Specific Options (MultiSwitch 900)53Chapter 555Removing the Cables, Connector and Module55Overview55Introduction55In This Chapter55Removing the Cables56Figure 5-1: Removing the LDM Port Cable56Removing the GBIC Card57Figure 5-2: GBIC Removal57Unseating the Module58Figure 5-3: Unseating the Module58Appendix A59Problem Solving59Overview59Introduction59In This Appendix59Normal Power-Up60LED Descriptions61Table A-1: Module LED States61Problem Solving Using LEDs63NOTE63Table A-2: Problem Solving Using the LEDs63Appendix B65Connector Pin Assignments and Adapters65Overview65In This Appendix65Connectors and Pin Assignments6610BaseT Port (8-pin MJ) Straight-through Connector66Figure B-1: 8-pin MJ Straight-through Connector66Table B-1: 8-pin MJ Straight-through Connector Pin Assignments66Adapters67H8571-J Adapter67Figure B-2: H8571-J Adapter67H8575-A Adapter68Figure B-3: H8575-A Adapter68Appendix C69Product Specifications69Overview69In This Appendix69Product Specifications70Table C-1: Product Specifications70Acoustical Specifications71Table C-2: Acoustical Specifications71Table C-3: German Acoustical Specifications71Connectors72Table C-4: Connectors72Size: 896 KBPages: 72Language: EnglishOpen manual