User ManualTable of ContentsPackard Bell1Packard Bell1EasyNote MT1Disassembly Manual1Disassembly Manual1Disassembly Manual1Disassembly Manual1Table of Contents2About this Guide3For More Information3Technician Notes3Disassembly3 Turn OFF the power to the system and all peripherals using the power button.3 Unplug the AC adapter and all power and signal cables from the system.3 Remove any SD/MMC card, ExpressCard or dummy card from the computer.3 Do not disassemble the system into parts that are smaller than those specified in the instructions.3 Label all removed connectors; note where the connector goes and in what position it was installed.3 The screws for the different components vary in size. During the disassembly process, group the screws with the corresponding components to avoid mismatch when putting back the components.3Reassembly3Required Tools3 Wrist grounding strap and conductive mat for preventing electrostatic discharge.3 Small Phillips screwdriver.3 Small flat screwdriver.3Hazardous Voltage4Avoid Electrostatic Discharge4Power Supply Unit4Power Supply Unit4Power Supply Unit4Power Supply Unit4WARNING4AVERTISSEMENT4WARNUNG4ADVERTENCIA4WAARSCHUWING4AVVERTENZA4Battery5Note: Use an anti-static mat or something soft like a piece of cloth underneath the notebook to prevent damage to the exterior of the notebook.5Fig. 1 Removing the battery.5Hard Disk Drive5Fig. 2 Removing hard disk drive compartment cover.5Fig. 3 Disconnecting and removing hard disk drive.6Fig. 4 Separating hard disk drive from bracket.6Note: In Fig. 4 only two screws are visible; the other two are located on the other side of the bracket.6Memory6Fig. 5 Removing memory compartment cover.7Fig. 6 Removing memory module.7Note: In case two memory modules have been installed, you have to remove the top module first before you can remove the one underneath.7Optical Disk Drive7Fig. 7 Location screw securing optical disk drive.8Fig. 8 Removing metal bracket.8Fig. 9 Location tray bezel lock underside.9Fig. 10 Location tray bezel side lock.9Note: The tray bezel is a delicate part, use care when handling it.9Keyboard9Fig. 11 Removing keyboard.10Fig. 12 Releasing keyboard flat cable.10Keyboard Cover10Fig. 13 Location keyboard cover screws.11Top Cover11Fig. 14 Location of wireless LAN compartment cover screw.11Fig. 15 Location of WiFi antenna cables.12Note: There are two WiFi antenna cables connected to the wireless LAN adapter. The black WiFi antenna cable is connected to MAIN (1) connector and the white WiFi antenna cable is connected to AUX (2) connector.12Fig. 16 Location of touchpad and button board flat cables.12Fig. 17 Location of top cover screws.13LCD Assembly13Fig. 18 Location LCD/webcam cables.13Fig. 19 Location LCD hinge screws.14Note: In Fig. 19, some of the screws are partly covered by adhesive tape and/or cables.14Speakers14Fig. 20 Location speaker screws.14Fig. 21 Location of speaker cable header on the main board.15Note: The left and right speaker assembly share the same header on the main board.15Bluetooth (Optional)15Fig. 22 Location of Bluetooth module.15USB Board16Fig. 23 Releasing the USB board cable.16Fig. 24 Location USB board screws.16Note: Optionally, you can disconnect the other end of the flat cable from the USB board.16Main Board16Fig. 25 Location of speaker brackets screws.17Fig. 26 Location of audio board cable.17Fig. 27 Location of main board screws.18Fig. 28 Location of main board bracket screws.18CMOS Battery18Fig. 29 Location CMOS battery.19Wireless LAN Adapter19Fig. 30 Location of wireless LAN adapter screws.19TV Tuner (Optional)19Fig. 31 Location of TV tuner screws.20Note: The EasyNote MT can have a TV tuner card installed or the Intel Turbo memory, not both.20Intel Turbo Memory (Optional)20Note: The EasyNote MT can have a TV tuner card installed or the Intel Turbo memory, not both.20CPU and Heat Sink20Fig. 32 Location of chipset heat sink screws.21Fig. 33 Location of CPU heat sink screws.21Fig. 34 Location of screw securing CPU.22I/O and HDMI Board22Fig. 35 Removing the I/O and HDMI board.22Note: Fig. 35 shows the other side of the main board, the screws are located on the other side of the main board.22Note: During re-assembly, align the I/O and HDMI board properly with the main board before reconnecting them to prevent damage to the pins of the connector on the main board.22Audio Board23Fig. 36 Releasing the audio board.23Note: Fig. 36 shows the audio cable still connected. However, this was disconnected at step 2 of the main board disassembly (see Main Board on page 15).23Subwoofer23Fig. 37 Location subwoofer screws.23TV Antenna (Optional)24Fig. 38 Location of TV antenna connector.24Touchpad24Fig. 39 Location touchpad cable and screws.24Note: The described procedure applies only to the touchpad module, which holds the touchpad buttons; the touchpad surface is part of the top cover.25Button Board25Fig. 40 Location of button board screws.25LCD Bezel25Fig. 41 LCD bezel screws.25Note: In Fig. 41, the screws in each of the lower corner are covered by cables.26Inverter Board26Fig. 42 Location of inverter board.26LCD Panel26Fig. 43 Location of bracket screws.26Fig. 44 Location of LCD cable connector.27Webcam/Microphone27Fig. 45 Location of webcam connector.27Fig. 45 Location of webcam connector.27Fig. 45 Location of webcam connector.27EasyNote MT Disassembly Manual28Size: 2.45 MBPages: 28Language: EnglishOpen manual