User ManualTable of ContentsMorphoAccess® J Series1Introduction51. Scope of the document 352. Safety instructions 45Terminal presentation51. Interfaces presentation 95Terminal configuration51. Setting up the terminal IP address 1552. Configuring a standalone MorphoAccess® 1653. Understanding MorphoAccess® configuration parameters management 1854. Configuring a networked MorphoAccess® 2065. Upgrading the firmware 2466. Downloading (adding) a licence 256Stand alone modes (networked or not)61. Recognition mode synthesis 2962. Adding a user’s record in the database 3063. Access control presentation 316Access control by identification61. Access control by identification 396Access control by authentification61. Introduction to authentication with contacless card 4362. Access control by authentication 457Proxy Mode71. Proxy mode (or slave) presentation 5772. Proxy mode activation 587Terminal Customization71. Setting up recognition mode 6172. Setting up matching threshold 6373. Relay activation 6474. LED IN feature 6675. Access request log file 6876. Remote messages: sending the User ID to the central security controller 6977. Anti-tamper and anti-pulling switches 7178. Setting up time mask 757Man Machine Interface81. Convention 7982. Identification - Waiting for a finger on the sensor 8083. Authentification - waiting for user's contactless card 8184. Multi-factor mode - waiting for user’s finger or contactless card 8285. Access granted 8386. Access denied 8487. Timeout while waiting for finger on the sensor 8588. No database or empty database 8689. USB mass storage key can be removed 87810. Terminal maintenance 88811. Sensor start up error 898Appendix81. MorphoAccess® 100 and 500 Series compatibility 9382. MorphoAccess® 200 and 300 Series compatibility 9583. Contactless Card modes table 9784. Required tags on User’s contactless card 9985. Troubleshooting 10086. Bibliography 1018Support91. Scope of the document152. Safety instructions16Europe information16USA information16Section 1131. Interfaces presentation21User interface21Power supply interface (see figures 2 • 2 and 2 • 3)22Administration interface (see figures 2 • 2 and 2 • 3)22Access control devices and systems interface (see figure 2 • 2)22Section 2191. Setting up the terminal IP address272. Configuring a standalone MorphoAccess®28"USB" key administration28Principle293. Understanding MorphoAccess® configuration parameters management30Presentation30Configuration organization30Modifying a parameter31Notation314. Configuring a networked MorphoAccess®32Introduction32Network factory settings33Date/Time settings33SSL securing33Modifying a configuration key using "configuration tool"33Network Wi-Fi™ configuration345. Upgrading the firmware366. Downloading (adding) a licence37Section 3251. Recognition mode synthesis412. Adding a user’s record in the database423. Access control presentation43Typical access control system43Identification - authentification44Access control result communication45Scope45"Proxy" mode47Section 4391. Access control by identification51Section 5491. Introduction to authentication with contacless card55Selecting the type of contactless card to be supported55Recognition modes552. Access control by authentication57Authentication with templates on a contactless card58Authentication with template in local database and user ID on contactless card59ASCII User ID included in a TLV structured data59Binary user’s identifier, non-structured data60Authentication based on contactless card mode62Bypassing the biometric control in authentication63The terminal controls that the user ID exists in the database63The terminal works only as a smart card reader64The terminal read binary ID on card and works as a smart card reader64Multi-factor mode65Section 6531. Proxy mode (or slave) presentation692. Proxy mode activation70Section 7671. Setting up recognition mode73Two attempts mode73Parameters732. Setting up matching threshold753. Relay activation76Relay external activation764. LED IN feature785. Access request log file806. Remote messages: sending the User ID to the central security controller81Presentation81Supported protocols82Note about terminal clock deviation827. Anti-tamper and anti-pulling switches83Description83Configuration keys848. Setting up time mask87Section 8711. Convention912. Identification - Waiting for a finger on the sensor923. Authentification - waiting for user's contactless card934. Multi-factor mode - waiting for user’s finger or contactless card945. Access granted956. Access denied967. Timeout while waiting for finger on the sensor978. No database or empty database989. USB mass storage key can be removed9910. Terminal maintenance10011. Sensor start up error101Section 9891. MorphoAccess® 100 and 500 Series compatibility1052. MorphoAccess® 200 and 300 Series compatibility1073. Contactless Card modes table1094. Required tags on User’s contactless card1115. Troubleshooting112Terminal IP address is unknown or terminal is not reachable112Sensor is off112Terminal returns erratic answers to ping requests1126. Bibliography113Administrator Information113Installation Information113Developer Information114Support Tools114Section 10103Customer service117Hotline117Section 11115Size: 4.49 MBPages: 118Language: EnglishOpen manual