User ManualTable of ContentsPrecautions2UBC72XLT Controls and Display3Contents4Introduction6Feature Highlights8About This Manual9Understanding Scanning11What is Scanning?11What is Searching?11Conventional Scanning11Where To Obtain More Information13Included With Your Scanner14Setting Up Your Scanner14Using Internal Batteries151. Make sure the power is turned off.152. Slide the battery compartment cover.153. Before you install alkaline or any other non- rechargeable batteries, use a pointed object such as a ballpoint pen to set REG. ALK. BATT./ NI-MH BATT. inside the compartment to REG. ALK. BATT..154. Install two batteries in the compartment as indicated by the polarity symbols (+ and -) marked inside.165. Replace the cover.176. When flashes and the scanner beeps every 15 seconds, replace both batteries.17Using AC Power19Connecting the Antenna19Connecting an Earphone/Headphone20Connecting an Extension Speaker20Attaching the Belt Clip21About Your Scanner22A Look At The Keypad23A Look At The Display26Understanding Banks28Operation29Turning On The Scanner and Setting Squelch291. Turn Squelch fully counterclockwise.292. Press and hold for about 2 seconds to turn the scanner on, then turn Volume clockwise until you hear a hissing sound.293. If the scanner is scanning, press Hold to stop scanning, then turn Squelch clockwise until the hissing stops.29Storing Known Frequencies Into Channels291. Press Hold. Then enter the channel number where you want to store a frequency, then press Func and Pgm. The channel number appears.292. Use the number keys and to enter the frequency (including the decimal point) you want to store.293. Press E to store the frequency into the channel.294. To program the next channel in sequence, press E/Pgm then repeat Steps 2 and 3.30Searching For and Temporarily Storing Active Frequencies301. Press Func and Pgm during service search or service search hold mode. The frequency and the lowest blank channel alternately appear.312. Press E to store the frequency into the blank channel. If you want to select another channel, press Func + or Func + before you press E. You can also use the 0-9 key to select the bank.31Scanning the Stored Channels31Manually Selecting a Channel32Special Features33Close CallTM RF Capture Technology331. Press Func then press and hold for 2 seconds. One of the following Close Call options appears.342. Repeatedly press or to select the option you want, then press E.343. Repeatedly press or until the band you want to search appears, then press E to select it. Otherwise, press if you do not want to select it.354. Repeatedly press or until the option you want appears, then press E to select it. Otherwise, press if you do not want to select it. Then skip to Step 9.355. Press E while C-C.Alt appears. One of the following alert options appears.356. Repeatedly press or until the option you want appears, then press E to select it. Otherwise, press if you do not want to select it. Then skip to Step 9.357. Press E while C-C.PS appears. One of the following Pager Screen options appears.368. Repeatedly press or until the option you want appears, then press E to select it.369. When you select the option, press Scan to start Close Call search. Otherwise, to continue normal scanning, repeatedly press Func until disappears then press Scan.36Chain Search371. Press Func + Pgm in chain search mode or chain search hold mode. The lowest blank channel and bank appear.382. Press E to store the frequency into the blank channel. To select another channel, press Func + or Func + before you press E. You can also press 0-9 to select the bank.381. Enter the lower limit frequency by using the 0-9 and keys.392. Press E to select the lower limit frequency.393. Enter the upper limit frequency by using the 0-9 and keys.394. Press E to select the upper limit frequency.39Direct Entry Search391. If the scanner is scanning or searching, press Hold.392. Enter the frequency you want to start from by using the number keys. (Press to enter a decimal point).403. Press Func + or Func + . The scanner searches, starting from the frequency you entered in Step 2.401. Press Func + Pgm in direct entry search mode or direct entry search hold mode. The frequency and lowest blank channel alternate on the display.412. Press E to store the frequency into the blank channel. To select another channel, repeatedly press Func + or Func + to select the blank channel you want, then press E. You can also use the 0-9 keys to select the bank.41Search Skip Memory411. Press Hold to stop the search.422. Press Func + or Func + to select the frequency. L/O appears.423. Press Func + L/O. L/O disappears.42Delay42Turning Channel-Storage Banks On and Off43Locking Out Channels44Priority441. Manually select the channel you want to select as the priority channel.452. Press Func + Pgm, then press Func + Pri. P appears to the left of the selected channel number.453. Repeat Steps 1 and 2 for the channel in each bank you want to program as a priority channel.45Using Keylock45Using the Display Backlight45Troubleshooting46Resetting the Scanner481. Turn off the scanner.482. While holding down 2, 9, and Hold, turn on the scanner. It takes about 3 seconds to initialize and CLEAr appears.48Care and Maintenance49General Use49Location49Cleaning49Repairs50Birdies50Specifications51Optional Accessories53One-Year Limited Warranty54Size: 916 KBPages: 56Language: EnglishOpen manual