User ManualTable of ContentsIntroduction7Projector Features7Package Contents8Projector with Lens Cap8AC Power Cord8VGA Cable (D-SUB to D-SUB)8User’s Manual8Projector Overview9Using the Product11Control Panel11Connection Ports12Remote Control13For the first time use:14For battery change:141. Push the catch to the right and remove the battery holder.142. Remove the old Lithium coin cell and install new one (CR2025). Ensure that the side with the mark “+” is up.143. Push the battery holder back into the remote control until you feel a click.14Remote Control Operation15Installation16Connecting the Projector16Powering On/Off the Projector17Powering On the Projector:171. Remove the projector lens cap.172. Complete the AC power cord and peripheral signal cable(s) connections.173. Press button to turn on the projector. The projector takes a minute or so to warm up.174. Turn on your source (computer, notebook, DVD, etc.). The projector automatically detects your source.17Powering Off the Projector:171. Press button to turn off the projector lamp. You will see a message "Power off? Press Power again" appear on the screen.172. Press button again to confirm.173. Disconnect the AC power cord from the electrical outlet and the projector.174. Do not turn on the projector immediately following a power off procedure.17Adjusting the Projector18Adjusting the Projector Height181. To raise or lower the image, press the elevator button and raise or lower the front of the projector. Release the button to lock the adjustment.182. To level the image on the screen, turn the tilt-adjustment foot to fine-tune the height.18Adjusting the Projector Zoom and Focus181. Focus the image by rotating the focus ring. A still image is recommended for focusing.182. Adjust the image by sliding the zoom ring.18Adjusting Projection Image Size19Maintenance24Cleaning the Lens24Cleaning the Projector Housing24Replacing the Lamp251. Turn off the projector.262. If the projector is installed in a ceiling mount, remove it from the mount.263. Unplug the power cord.264. Loosen the screw in the side of the lamp cover and remove the cover.265. Remove the screws from the lamp module, raise the handle, and lift out the module.266. Insert the new lamp module into the projector and tighten the screws.267. Replace the lamp cover and tighten the screw.268. Turn on the projector. If the lamp does not turn on after the warm-up period, try reinstalling the lamp.269. Reset the lamp hour. Refer to the “Setting” menu.26Appendix28LED Indicator Messages28Compatibility Modes29Computer:29Video:29Troubleshooting30Start-up problems30Image problems30Notes on the AC Power Cord7Menu Operation20Specifications27Size: 1.58 MBPages: 36Language: EnglishOpen manual
User ManualTable of ContentsIntroduction7Projector Features7Package Contents8Projector with Lens Cap8AC Power Cord8VGA Cable (D-SUB to D-SUB)8User’s Manual8Projector Overview9Using the Product11Control Panel11Connection Ports12Remote Control13For the first time use:14For battery change:141. Push the catch to the right and remove the battery holder.142. Remove the old Lithium coin cell and install new one (CR2025). Ensure that the side with the mark “+” is up.143. Push the battery holder back into the remote control until you feel a click.14Remote Control Operation15Installation16Connecting the Projector16Powering On/Off the Projector17Powering On the Projector:171. Remove the projector lens cap.172. Complete the AC power cord and peripheral signal cable(s) connections.173. Press button to turn on the projector. The projector takes a minute or so to warm up.174. Turn on your source (computer, notebook, DVD, etc.). The projector automatically detects your source.17Powering Off the Projector:171. Press button to turn off the projector lamp. You will see a message "Power off? Press Power again" appear on the screen.172. Press button again to confirm.173. Disconnect the AC power cord from the electrical outlet and the projector.174. Do not turn on the projector immediately following a power off procedure.17Adjusting the Projector18Adjusting the Projector Height181. To raise or lower the image, press the elevator button and raise or lower the front of the projector. Release the button to lock the adjustment.182. To level the image on the screen, turn the tilt-adjustment foot to fine-tune the height.18Adjusting the Projector Zoom and Focus181. Focus the image by rotating the focus ring. A still image is recommended for focusing.182. Adjust the image by sliding the zoom ring.18Adjusting Projection Image Size19Menu Operation201. Press the Menu button to open the OSD menu.212. When OSD is displayed, use p / q to select any feature in the main menu.213. After selecting the desired main menu feature, press u to enter sub-menu for feature setting.214. Adjust the settings with t / u.215. Press the Menu button, the screen will return to the main menu.216. To exit OSD, Press the Menu button again. The OSD menu will close and the projector will automatically save the new settings.21Maintenance24Cleaning the Lens24Cleaning the Projector Housing24Replacing the Lamp251. Turn off the projector.262. If the projector is installed in a ceiling mount, remove it from the mount.263. Unplug the power cord.264. Loosen the screw in the side of the lamp cover and remove the cover.265. Remove the screws from the lamp module, raise the handle, and lift out the module.266. Insert the new lamp module into the projector and tighten the screws.267. Replace the lamp cover and tighten the screw.268. Turn on the projector. If the lamp does not turn on after the warm-up period, try reinstalling the lamp.269. Reset the lamp hour. Refer to the “Setting” menu.26Appendix28LED Indicator Messages28Compatibility Modes29Computer:29Video:29Troubleshooting30Start-up problems30Image problems30Notes on the AC Power Cord7Size: 1.81 MBPages: 36Language: EnglishOpen manual
