Cable Electronics HSW88C Manual De Usuario
Method A:
Push Button
1. Use the switch button on output port to select which port to be
changed.
changed.
(+) increase (–) decrease
2. Push the switch button on Input channel. The source will be
sequentially changed. After few seconds, the setting will be active.
sequentially changed. After few seconds, the setting will be active.
Method B:
IR Remote Control
a. Please press F1 to F8 Enter IR control mode and decide which output
port to be controlled (see the table below), and wait a few seconds for
the output port seven segment display to show the number of selected
output port. Or you can use up ( ) and down ( ) button to enter IR
control mode and select the output port in ascending and descending
order respectively.
Note:
port to be controlled (see the table below), and wait a few seconds for
the output port seven segment display to show the number of selected
output port. Or you can use up ( ) and down ( ) button to enter IR
control mode and select the output port in ascending and descending
order respectively.
Note:
b. Use left ( ) or right ( ) button to select input source as indicated
by the seven segment display on the front panel for the input
channel. The setting will be active once the channel switch
command is set after a couple seconds.
channel. The setting will be active once the channel switch
command is set after a couple seconds.
Note:
Right ( ) button to switch input source in ascending order
Right ( ) button to switch input source in ascending order
(1, 2, 3, 4, 5, 6, 7, 8, 1, ...)
Left ( ) button to switch input source in descending order
Left ( ) button to switch input source in descending order
(1, 8, 7, 6, 5, 4, 3, 2, 1, …)
SOURCE SIDE
CHANNEL CONTROL
F1
HDMI output port #1
F2
HDMI output port #2
F3
HDMI output port #3
F4
HDMI output port #4
F5
HDMI output port #5
F6
HDMI output port #6
Enter (
)
HDMI output port #7
Exit ( )
HDMI output port #8
Up ( )
Switch output port in ascending
order
Down ( )
Switch output port in descending
PANEL DESCRIPTIONS
1. Power: Power control
2. Seven Segment LED Indicators: Control display
3. Front panel push buttons: Used to input source and display channel
number
4. IR: IR receiver
2. Seven Segment LED Indicators: Control display
3. Front panel push buttons: Used to input source and display channel
number
4. IR: IR receiver
5. AC Power: 100-240V
6. RS-232: RS-232 control port
7. USB: USB control port
8. SW Main: DIP switches (see DIP Switch section in p.8)
9. SW 1–8: DIP switch (see DIP Switch section in p.8)
10. INPUT 1 –8: HDMI inputs
11. IR PASS-THROUGH 1–8: 3.5mm IR blaster socket for individual HDMI
source control
12. OUPUT PORT 1–8: RJ-45 outputs for each output channel
13. IR Main: 3.5mm IR blaster socket for HDMI source control on all 8
inputs [default socket for IR blaster]
6. RS-232: RS-232 control port
7. USB: USB control port
8. SW Main: DIP switches (see DIP Switch section in p.8)
9. SW 1–8: DIP switch (see DIP Switch section in p.8)
10. INPUT 1 –8: HDMI inputs
11. IR PASS-THROUGH 1–8: 3.5mm IR blaster socket for individual HDMI
source control
12. OUPUT PORT 1–8: RJ-45 outputs for each output channel
13. IR Main: 3.5mm IR blaster socket for HDMI source control on all 8
inputs [default socket for IR blaster]
6
9
1
9
12
13 8
7
9
9
11
1
1
2
3
4