Star Trac S-TBTX Manual De Usuario
STAR
TRAC
S-TBT
X
TOTAL
BODY
TRAINER
O
WNER
’
S
M
ANUAL
27
(Spanish), LDU (Dutch), LPO (Portuguese), LFR (French), LIT (Italian), LSW
(Swedish) or LKA (Katakana).
LOE
OFF
ON
OFF
Lockout Enable. Enables/disables lockout function.
LOI
001
999
001
Lockout ID. Lockout override identification number.
MAINTENANCE MODE
Your Service Representative may need to check accumulated data about the past usage of your trainer, test its display controls,
or investigate error messages. For these reasons, your trainer is equipped with a Maintenance Mode. The Maintenance Mode
includes all of the items available through Manager Mode, plus additional items for Service and Diagnostic use. To enter
includes all of the items available through Manager Mode, plus additional items for Service and Diagnostic use. To enter
Maintenance Mode:
1. Press and hold the
,
and
keys together.
2. A beep will sound and “MAINTENANCE SETTINGS” will scroll once across the P
ROFILE
Window.
3. Release all keys. “SN” will display in the P
ROFILE
Window; the associated numeric value for the parameter will display
in the D
ISTANCE
Window.
NOTE:
The system will automatically exit MAINTENANCE SETTINGS if no key is pressed for 30 seconds.
The following keys are used to modify MAINTENANCE SETTINGS:
Increase and Decrease Level Keys:
Display the next (Increase) and previous (Decrease) parameters. Keys will
repeat if held.
Numeric Keypad:
Facilitates entry of the desired value for the displayed parameter. These keys do not save the
new value – see OK Key below.
OK Key:
Updates (saves) the value of the displayed parameter in Flash memory. “UPDATING” will scroll once
across the P
ROFILE
Window while the update is in process. When the update is complete, the P
ROFILE
Window will
show the new value for the parameter.
NOTE:
To exit MAINTENANCE SETTINGS without saving any values or settings, press the Q
UICK
S
TART
key.
NOTE:
Unless otherwise specified, the
Item (parameter) name is shown in the P
ROFILE
Window, and the value of the parameter is
shown in the D
ISTANCE
Window.
The items that you may display and change with the previous keys are:
Item
Lowest
Value
Highest
Value
Default
Value
Meaning
SN
0
9999
N/A
Serial Number. Total Body Trainer serial number (set by factory).
DSW
1.0
99.99
N/A
Display Software. Display panel software version number (set by factory).
NOTE:
NOTE:
Software checksum value is displayed in C
ALORIES
Window.
OHR
0
9999
0
Operating Hours. Total operating hours.
DST
0
9999
0
Distance. Total distance traveled in miles or kilometers, based on current UNx
setting.
setting.
UNx
UNE
UNM
UNE
Units. UNE (English) = units of pounds, miles, feet, inches
UNM (Metric) = units of kilograms, kilometers, centimeters
NOTE: Current Value is shown in P
ROFILE
Window.
TIM
5
99
99
Time. Maximum time in minutes allowed for a program, excluding warm-up
and cooldown.
and cooldown.
WGT
1 (lb)
1 (kg)
1 (kg)
500 (lb)
226 (kg)
226 (kg)
155 (lb)
70 (kg)
70 (kg)
Default Weight (to user). Typical weight in lb (UNx = UNE) or kg (UNx =
UNM).
UNM).
Lxx
N/A
N/A
LEN
Language. Display language; either LEN (English), LGE (German), LSP
(Spanish), LDU (Dutch), LPO (Portuguese), LFR (French), LIT (Italian), LSW
(Spanish), LDU (Dutch), LPO (Portuguese), LFR (French), LIT (Italian), LSW