Tunturi E85S Manual De Usuario
GB
O W N E R ’ S M A N U A L
•
E 8 5 S E 8 5
11
Never remove the equipment’s protective casing.
The electromagnetic brake forms a magnetic field that
may damage the mechanism of a watch, or the magnetic
identification strip on a credit or cash card, should they
come into immediate contact with the magnets. Never
attempt to detach or remove the electromagnetic brake!
may damage the mechanism of a watch, or the magnetic
identification strip on a credit or cash card, should they
come into immediate contact with the magnets. Never
attempt to detach or remove the electromagnetic brake!
The electromagnetic brake is based on electromagnetic
resistance; resistance level is electronically measured
and shown as watt reading on the display. Due to the
measurement system, your Tunturi ergometer need not
be re-calibrated when assembled, serviced and used
according to this Owner’s Manual.
resistance; resistance level is electronically measured
and shown as watt reading on the display. Due to the
measurement system, your Tunturi ergometer need not
be re-calibrated when assembled, serviced and used
according to this Owner’s Manual.
If the equipment is not used for a period of time, the
transmission belt may become temporarily distorted.
This can lead to a sensation of slightly uneven pedaling.
However, after a few minutes of use the effect disappears
as the belt returns to its original form.
transmission belt may become temporarily distorted.
This can lead to a sensation of slightly uneven pedaling.
However, after a few minutes of use the effect disappears
as the belt returns to its original form.
MALFUNCTIONS
Despite continuous quality control, defects and
malfunctions caused by individual components may
occur in the equipment. In most cases it’s unnecessary
to take the whole device in for repair, as it’s usually
sufficient to replace the defective part.
malfunctions caused by individual components may
occur in the equipment. In most cases it’s unnecessary
to take the whole device in for repair, as it’s usually
sufficient to replace the defective part.
If the equipment does not function properly during use,
contact your Tunturi dealer immediately. Always give
the model and serial number of your equipment. Please
state also the nature of the problem, conditions of use
and purchase date.
contact your Tunturi dealer immediately. Always give
the model and serial number of your equipment. Please
state also the nature of the problem, conditions of use
and purchase date.
If you require spare parts, always give the model, serial
number of your equipment and the spare part number
for the part you need. The spare part list is at the back
of this manual. Use only spare parts mentioned in the
spare part list.
number of your equipment and the spare part number
for the part you need. The spare part list is at the back
of this manual. Use only spare parts mentioned in the
spare part list.
MAINTENANCE MENU
The meter features a Maintenance menu, which can be
accessed in the Start menu by pressing ZOOM for 3
seconds. You can navigate the Maintenance menu with
the arrow keys and confirm your selections by pressing
ENTER.
accessed in the Start menu by pressing ZOOM for 3
seconds. You can navigate the Maintenance menu with
the arrow keys and confirm your selections by pressing
ENTER.
A)
Start menu = exit the maintenance menu and return
to the Start menu.
B)
Total training values = total training time and
distance on the equipment. Use Reset to reset both
values.
values.
C)
Software update = the display shows the meter’s
software version. You can use the Update function to
upgrade the software version.
upgrade the software version.
D)
Audio signals = set the meter’s audio signals on or off.
E)
Display = adjust display contrast
TRANSPORT AND STORAGE
Please follow these instructions when carrying and
moving the cycle about, because lifting it incorrectly
may strain your back or risk other accidents:
moving the cycle about, because lifting it incorrectly
may strain your back or risk other accidents:
NOTE!
Always switch the power off and unplug the
power cord before you start moving the equipment
around!
around!
Stand behind the equipment. Grip the seat with one
hand and the handlebar with the other, and set your
foot on the rear support. Tilt the equipment so that
it rests on its transport wheels. Wheel the equipment
to move it, on these transport wheels. Lower the
equipment while holding on to the handlebar and
remain behind the equipment all the time.
hand and the handlebar with the other, and set your
foot on the rear support. Tilt the equipment so that
it rests on its transport wheels. Wheel the equipment
to move it, on these transport wheels. Lower the
equipment while holding on to the handlebar and
remain behind the equipment all the time.
NOTE!
Transport the equipment with caution over uneven
surfaces, for example over a step. The equipment should
never be transported upstairs using the wheels over
the steps, instead it must be carried. We recommend
that you use a protective base when transporting the
equipment.
surfaces, for example over a step. The equipment should
never be transported upstairs using the wheels over
the steps, instead it must be carried. We recommend
that you use a protective base when transporting the
equipment.
To prevent the equipment malfunctioning, store in a dry
place with as little temperature variation as possible and
protected from dust.
place with as little temperature variation as possible and
protected from dust.
TECHNICAL SPECIFICATIONS
E85S
Length.......................................... 98
cm
Width ......................................... 64 cm
Height ......................................... 104 cm
Weight ........................................ 35 kg
Height ......................................... 104 cm
Weight ........................................ 35 kg
E85
Length.......................................... 96
cm
Width ......................................... 64 cm
Height ......................................... 116 cm
Weight ........................................ 44 kg
Height ......................................... 116 cm
Weight ........................................ 44 kg
The Tunturi ergometer models E85S and E85 meet
the requirements of the EU’s EMC Directives on
electromagnetic compatibility (89/336/EEC) and
electrical equipment designed for use within certain
voltage limits (73/23/EEC). This product therefore
carries the CE label.
the requirements of the EU’s EMC Directives on
electromagnetic compatibility (89/336/EEC) and
electrical equipment designed for use within certain
voltage limits (73/23/EEC). This product therefore
carries the CE label.
The Tunturi ergometer models E85S and E85 meet EN
precision and safety standards (Class SHA, EN-957,
parts 1 and 5).
precision and safety standards (Class SHA, EN-957,
parts 1 and 5).
Due to our continuous policy of product development,
Tunturi reserves the right to change specifications
without notice.
Tunturi reserves the right to change specifications
without notice.
NOTE!
The instructions must be followed carefully in
the assembly, use and maintenance of your equipment.
The warranty does not cover damage due to negligence
of the assembly, adjustment and maintenance
instructions described herein. Changes or modifications
not expressly approved by Tunturi Oy Ltd will void the
user’s authority to operate the equipment!
The warranty does not cover damage due to negligence
of the assembly, adjustment and maintenance
instructions described herein. Changes or modifications
not expressly approved by Tunturi Oy Ltd will void the
user’s authority to operate the equipment!
We wish you many enjoyable trainings with your
new Tunturi training partner!
new Tunturi training partner!
E85S__E85manual.indd 11
5.10.2004, 14:40:53