Casio 5216 Manual De Usuario

World Time digitally displays the current time in 48 cities 
(31 time zones) around the world.

 All of the operations in this section are performed in 

 

x

the World Time Mode, which you enter by pressing 

C 

(page E-6).

 If the hour and minute hands are not in the correct positions, use 

 

x

D (+) and B 

(–) to adjust them.
 If the left dial hand is not in the correct position, use 

 

x

C to adjust it.

 Holding down 

 

x

D, B, or C for a few seconds will start high-speed movement 

of each hand (which will continue even if you release the button). To stop high-
speed hand movement, press any button.
 

 

x D, B and C high-speed hand movement will also stop automatically as 

described below.

 

 

−

D : After 12 revolutions of the minute hand
 

 

−

B : After one revolution of the minute hand
 

 

−

C : After one revolution of the left dial hand

 After everything is the way you want, press 

2. 

A to return to the Timekeeping Mode.

 After performing home position adjustment, enter the Timekeeping Mode and check 

 

x

to make sure that the analog hands and the digital display indicate the same time. If 
they do not, perform home position adjustment again.

Strong magnetism or impact can cause the hands of the watch to be off. If this 
happens, perform the applicable home position adjustment procedures in this section.

 Hand home position adjustment is not required if the analog time and digital time are 

 

x

the same in the Timekeeping Mode.

 In the Timekeeping Mode, hold down 

1. 

A for about fi ve 

seconds. You can release the button after “H-SET” 
appears on the display.

 Though “

 

x

ADJ” will appear on the display after about 

two seconds, do not release the button yet. Keep it 
depressed until “H-SET” appears.
 “

 

x 0:00” will fl ash on the display and the hour, minute, 

and left dial hands should move to 12 o’clock (their 
home positions).

Analog Timekeeping
The analog time of this watch is synchronized with the digital time. The analog time 
setting is adjusted automatically whenever you change the digital time.

 The hands for the analog timepiece move to adjust to a new setting whenever any 

 

x

of the following occurs.

 If the analog time does not match the digital time for any reason, use the procedure 

 

x

described under “To adjust home positions” (page E-17) to match the analog setting 
to the digital setting.
 Whenever you need to adjust both the digital and the analog time settings manually, 

 

x

make sure you adjust the digital setting fi rst.
 Depending on how much the hands have to move in order to adjust to the digital 

 

x

time, it may take some time before they stop moving.

 In the Timekeeping Mode, hold down 

1. 

A until “ADJ” 

appears on the display. Release 

A and the city code 

of your currently selected Home City will fl ash on the 
display, which indicates the setting screen.
 Press 

2. 

C to display the DST setting screen.

 Press 

3. 

D to toggle between Daylight Saving Time (

 

displayed) and Standard Time (

 displayed).

 Press 

4. 

A to exit the setting screen.

 The DST indicator appears on the Timekeeping, Alarm, 

 

x

and Hand Setting Mode to indicate that Daylight Saving 
Time is turned on.

Press 

5. 

A to exit the setting screen.

 The analog time will automatically change so it is synchronized with the digital time 

 

x

settings you confi gured.
 See “Digital Time Daylight Saving Time (DST) Setting” below for details about the 

 

x

DST setting.
 The 12-hour/24-hour timekeeping format you select in the Timekeeping Mode is 

 

x

applied in all modes.
 For details about illumination duration, see “Illumination” on page E-32.

 

x
Digital Time Daylight Saving Time (DST) Setting
Daylight Saving Time (summer time) advances the digital time setting by one hour 
from Standard Time. Remember that not all countries or even local areas use Daylight 
Saving Time.

Change the Home City code

Use 

D (east) and B (west). 

Toggle between Daylight Saving Time (

) and 

Standard Time (

)

Press 

D.

Toggle between 12-hour (

) and 24-hour 

(

) timekeeping

Reset the seconds to 

Change the hour or minutes

Use 

D (+) and B (–).

Change the year

Change the month or day

Toggle the button operation tone between 

 

(on) and 

 (off)

Press 

D.

Select one second (

) or three seconds 

(

) as the illumination duration

 Press 

3. 

C to move the fl ashing in the sequence shown below to select the other 

settings.

C

C

C

C

C

C

C

C

C

C

Home City Code

C

DST

12/24-Hour 

Format

Hour

Seconds

Year

Month

Day

Illumination Duration

Button Operation Tone

Minutes

 When the setting you want to change is fl ashing, use 

4. 

B and D to change it as 

described below.

 In the Timekeeping Mode, hold down 

1. 

A until “ADJ” 

appears on the display. Release 

A and the city code 

of your currently selected Home City will fl ash on the 
display, which indicates the setting screen.
 Use 

2. 

B and D to scroll through the city codes until the 

one you want is displayed.

 Make sure you select your Home City code before 

 

x

changing any other setting.
 For full information on city codes, see the “City Code 

 

x

Table” at the back of this manual.

Digital Time and Date
Use the Timekeeping Mode to set and view a digital display of the current time and 
date.
When setting the digital time, you can also confi gure settings for summer time 
(Daylight Saving Time or DST), your Home City code (the code for the city where you 
normally use the watch), the 12/24-hour format, and the illumination duration.

 This watch is preset with a number of city codes, each of which represents the time 

 

x

zone where that city is located. When setting the digital time, it is important that you 
select the correct city code for your Home City. If your location is not included in the 
preset city codes, select the preset city code that is in the same time zone as your 
location. 
 Note that all of the times for the World Time Mode city codes (page E-19) are 

 

x

displayed in accordance with the digital time and date settings you confi gure in the 
Timekeeping Mode.
 After you correctly set your Home City time and date, you can set the watch up for 

 

x

timekeeping with a different city code simply by changing the Home City code in the 
Timekeeping Mode.