Casio MO0406-EA Manual De Usuario
Operation Guide 3364 3365
3
To set the alarm time
1. In the Alarm Mode, press D to display the alarm
screen.
2. Hold down A until the hour setting of the alarm time
starts to flash, which indicates the setting screen.
• This operation automatically turns on the alarm.
3. Press C to move the flashing between the hour and
minute settings.
4. While a setting is flashing, use D (+) and B (–) to
change it.
• When setting the alarm time using the 12-hour format,
take care to set the time correctly as a.m. (no
indicator) or p.m. (P indicator).
indicator) or p.m. (P indicator).
5. Press A to exit the setting screen.
Alarm Operation
The alarm sounds at the preset time for about 10 seconds, regardless of the mode the
watch is in.
The alarm sounds at the preset time for about 10 seconds, regardless of the mode the
watch is in.
l ll
lll
ll
ll
l
Alarm time
(Hour : Minutes)
(Hour : Minutes)
• To stop the alarm tone after it starts to sound, press any button.
• Alarm and Hourly Time Signal operations are performed in accordance with the
Timekeeping Mode digital time.
To test the alarm
In the Alarm Mode, hold down D to sound the alarm.
In the Alarm Mode, hold down D to sound the alarm.
To turn the alarm and the Hourly Time Signal on and off
1. In the Alarm Mode, press D to select the alarm or the
Hourly Time Signal screen.
2. Press A to toggle the currently selected function on
(
Oo
displayed) and off (
Ow
displayed).
• The alarm on indicator and the Hourly Time Signal on
indicator remain on the display in all modes while these
functions are turned on.
functions are turned on.
Hourly time signal
on indicator
on indicator
Alarm on indicator
On/Off status
Stopwatch
The stopwatch lets you measure elapsed time, split times,
and two finishes.
and two finishes.
• The display range of the stopwatch is 59 minutes, 59.99
seconds.
• The stopwatch continues to run, restarting from zero
after it reaches its limit, until you stop it.
• Exiting the Stopwatch Mode while a split time is frozen
on the display clears the split time and returns to
elapsed time measurement.
elapsed time measurement.
• The elapsed time measurement operation continues
even if you exit the Stopwatch Mode.
• All of the operations in this section are performed in the
Stopwatch Mode, which you enter by pressing C.
STW
Minutes
Seconds
To measure times with the stopwatch
1/100 second
Minutes’ Seconds
lll
lllll
l
llll
lll
ll
l
D
Start
Stop
*
1
Elapsed Time
➤
Re-start
Clear
D
➤
Stop
*
1
D
➤
D
➤
A
*
1 When elapsed time measurement is stopped, the display alternates between a
minute and seconds screen, and a 1/100 second screen at 2-second intervals.
Split Time
D
D
Start
Split
*
2
➤
Split release
Clear
A
➤
Stop
*
1
A
➤
D
➤
A
*
2 Split times are displayed by cycling alternately through the split indicator (
SPL
),
a minute and seconds screen, and a 1/100 second screen.
Two Finishes
D
D
Start
Split
*
2
➤
Split stop
*
3
Clear
A
➤
Split release
*
1
D
➤
A
➤
A
First runner
finishes.
Display time of
first runner.
finishes.
Display time of
first runner.
Second runner
finishes.
finishes.
Display time of
second runner.
second runner.
*
3 When a split time operation is stopped, the display cycles through the same values
as those described in *2 above. In this case, however, the minute symbol ( ') and
the seconds symbol ( '') do not flash.
the seconds symbol ( '') do not flash.
Illumination
Two LEDs (light-emitting diodes) illuminate the face of the
watch for easy reading in the dark. The watch's auto light
switch automatically illuminates the face when you angle
the watch towards your face.
watch for easy reading in the dark. The watch's auto light
switch automatically illuminates the face when you angle
the watch towards your face.
• The auto light switch must be turned on (indicated by
the auto light switch on indicator) for it to operate.
• You can specify 1.5 seconds or 3 seconds as the
illumination duration.
• See “Illumination Precautions” for other important
information.
To illuminate the face of the watch manually
In any mode (except when a setting screen is on the display), press B to illuminate
the face of the watch.
In any mode (except when a setting screen is on the display), press B to illuminate
the face of the watch.
• The above operation turns on illumination regardless of the current auto light switch
setting.
Auto light switch
on indicator
on indicator
Parallel to
ground
ground
More than
40°
40°
About the Auto Light Switch
Turning on the auto light switch causes the face to illuminate, whenever you position
your wrist as described below in any mode. Note that this watch features a “Full Auto
LED Light”, so the auto light switch operates only when available light is below a
certain level. It does not illuminate the face under bright light.
Turning on the auto light switch causes the face to illuminate, whenever you position
your wrist as described below in any mode. Note that this watch features a “Full Auto
LED Light”, so the auto light switch operates only when available light is below a
certain level. It does not illuminate the face under bright light.
Moving the watch to a position that is parallel to the ground and then tilting it
towards you more than 40 degrees causes illumination to turn on.
towards you more than 40 degrees causes illumination to turn on.
• Wear the watch on the outside of your wrist.
Warning!
• Always make sure you are in a safe place whenever you are reading the face
of the watch using the auto light switch. Be especially careful when running or
engaged in any other activity that can result in accident or injury. Also take
care that sudden illumination by the auto light switch does not surprise or
distract others around you.
engaged in any other activity that can result in accident or injury. Also take
care that sudden illumination by the auto light switch does not surprise or
distract others around you.
• When you are wearing the watch, make sure that its auto light switch is turned
off before riding on a bicycle or operating a motorcycle or any other motor
vehicle. Sudden and unintended operation of the auto light switch can create a
distraction, which can result in a traffic accident and serious personal injury.
vehicle. Sudden and unintended operation of the auto light switch can create a
distraction, which can result in a traffic accident and serious personal injury.
To turn the auto light switch on and off
In any mode (except when a setting screen is on the display), hold down B for about
two seconds to toggle the auto light switch on (
In any mode (except when a setting screen is on the display), hold down B for about
two seconds to toggle the auto light switch on (
displayed) and off (
not
displayed).
• The auto light switch on indicator (
) is on the display in all modes while the auto
light switch is turned on.
• The auto light switch turns off automatically whenever battery power drops to Level
3.
• The auto light switch is disabled, regardless of its on/off setting, when the Hand
Setting Mode’s setting screen.
To specify the illumination duration
1. While any screen other than the last signal screen is on
the display in the Timekeeping Mode, hold down A
until the city code starts to flash, which indicates the
setting screen.
until the city code starts to flash, which indicates the
setting screen.
2. Press C three times to move the flashing to the
seconds setting.
3. Press B to toggle the illumination duration setting
between 3 seconds ( ) and 1.5 seconds (
).
4. Press A to exit the setting screen.
l l l l l ll
lll
ll
ll
Timekeeping
Use the Timekeeping Mode to set and view the current time and date. This section
also explains how to manually set the current date and time.
also explains how to manually set the current date and time.
• All of the operations in this section are performed in the Timekeeping Mode, which
you enter by pressing C.
▲
Time
Seconds
Date
▲
▲
Press A.
Month. Day
Hour : Minutes
PM indicator
▲
Day of week
▲
Press D.
Last Signal
Screens
2 seconds
A
A
Setting the Digital Time and Date Manually
Make sure you select your Home City code before you change the current time and
date settings. World Time Mode times are all displayed in accordance with the
Timekeeping Mode settings. Because of this, World Time Mode times will not be
correct if you do not select the proper Home City code before setting the time and
date in the Timekeeping Mode.
Make sure you select your Home City code before you change the current time and
date settings. World Time Mode times are all displayed in accordance with the
Timekeeping Mode settings. Because of this, World Time Mode times will not be
correct if you do not select the proper Home City code before setting the time and
date in the Timekeeping Mode.
To set the current digital time and date manually
1. While any screen other than the last signal screen is on
the display in the Timekeeping Mode, hold down A
until the city code starts to flash, which indicates the
setting screen.
until the city code starts to flash, which indicates the
setting screen.
• See “City Code Table” for a complete list of available
city codes.
2. Press C to move the flashing in the sequence shown
below to select other settings.
l l l l l
ll
ll
ll
ll
ll
l
Seconds
Hour
Minutes
12/24-Hour
Format
Format
Month
Year
DST
Day
Power
Saving
Saving
City Code