Coleman 2000002596 Manual De Usuario

2. Assemble six, steel, shock-corded, Leg Poles.
(Fig.

3. Push down on steel button on tapered end

and insert into end with four holes.

NOTE: Make sure steel button locks into

third hole on pole as shown. (Fig. 2)

4. Assemble three, steel, shock-corded, curved

Ridge Poles. (Fig. 1)

5. Stretch four corners of tent until taut; then

drive plastic stake web strap of each to

secure. (Fig. 3)

ROCKWALL

12 TENT

MODEL 2000002596

STITCH LINE

To Set Up Tent

1. Unfold tent and spread out on a clean, level surface with the door

facing the desired direction.

8. Rotate all six Leg Poles upright and insert pin on each web

loop at the side locations as shown. (Fig. 7 & 7A)

(continued on other side)

Pole Descriptions

Pole

Pole Pole

Description

Qty.

Dia.

Repair Kit

Replacement Kit

Long Leg Pole, steel
(w/ red marking)

19mm

N/A

5010000678

Short Leg Pole, steel

19mm

N/A

5010000680

Curved Ridge Pole, steel
(w/ red marking)

19mm

N/A

5010000677

Curved Ridge Pole, steel

19mm

N/A

5010000679

Vertical Door Pole, black,
short w/rubber tips

6.3mm 5010000543

5010000545

Door Pole, black,
long w/rubber tips

6.3mm 5010000543

5010000545

Fig. 3

9. Stretch tent to finished size:

• Push in button on Leg Pole while

twisting lower Leg Pole section

counterclockwise

(Fig.

8);

• Pull up on top Leg Pole section until

tent is taut;

• Twist the lower Leg Pole clockwise

until the button locks into the center

or lowest hole;

• Repeat on remaining Leg Poles.

10. Locate Frame Clips on front and back of

tent; then attach to Leg Poles as shown.

(Fig.

11. Insert plastic stakes through

web straps located at bottom
of each Leg Poles; then drive
in to secure. (Fig. 10)

Fig. 8

Button

Center Hole

Lower Hole

Lower
Leg Pole
Section

Upper
Leg Pole
Section

Button in

third hole

Fig. 2

Curved Ridge Poles (3)

Leg Poles,

short (4)

Leg Poles,

long (2)

Fig. 1

6. Insert Ridge Pole (with red marking) into center sleeve on top of tent

with the red trim (Fig. 4 & 6). Insert the remaining curved Ridge Poles

into the other two sleeves on top of tent.

7. Insert curved end of Leg Pole (with red marking) into the ends of the

Ridge Pole (with red dot). Insert curved end of remaining short Leg

Poles into the ends of the remaining Ridge Poles. (Fig. 5 & 6)

Curved

Ridge Pole

with Red

Marking

Fig. 4

Sleeve

with Red

Trim

Ridge Pole with

Red Marking

Fig. 5

Sleeve

with Red

Trim

Curved End of

Long Leg Pole

Door

Curved Ridge Pole

in sleeve

Fig. 6

Long Leg Pole

Curved Ridge Pole in

sleeve with Red Marking

Short Leg Pole

Front of Tent

Short Leg Pole

Curved Ridge Pole

in sleeve

Fig. 10

Fig. 9

Fig. 7

Hinged, Rigid Door

1. Assemble Vertical Door Pole (shorter black pole with plastic tips);

then insert through zippered vertical pole sleeve on hinged side of

door. (Fig. 11)

2. Insert end of Vertical Door Pole into bottom hinge plate, apply

pressure to form a slight bow, then insert other tip of pole into top

hinge. Zip up vertical pole sleeve. (Fig. 12 & 13)

3. Assemble Door Pole (longer black pole with plastic cap tips); then

insert into zippered pole sleeve at top of door. (Fig. 14)

4. Insert end of Door Pole into top hinge plate, apply pressure to form

a bow, then insert other tip of pole into the bottom hinge. (Fig. 15)

5. Zip up pole sleeve to enclose Door Pole. (Fig. 16)

Fig. 11

Fig. 12

Fig. 13

Vertical Pole

Sleeve

Door Hinge

Fig. 14

Fig. 15

Fig. 16

Pole

Sleeve

Top

Door

Hinge

Pole

Sleeve

Top

Door

Hinge

Before you begin

Read all instructions before set up.
• Select a level site clear of rocks, branches, and other hard or sharp

objects, to install your tent.
WARNING: Keep clear of overhead power lines

• Do not set up your tent under trees because of potential lightning strikes

or falling tree limbs in inclement weather.

• Secure with all stakes and guylines provided to prevent property damage

or personal injury.

• For best results in windy conditions, position narrow end of tent into
the

wind.

• Enlist the help of at least one other person to assist you when it is time
to assemble the tent.

Self-Rolling Window Spring Descriptions

Color Code Description

Qty.

Length

Replacement Part No.

Green

610mm 5010000627

Orange

670mm 5010000628

CAUTION: “Springs” may have sharp edges. Handle with care to avoid
injury. Keep out of reach of children.