Casio SCR-100-1 Manual De Usuario

7. Press one of the START buttons (

 or 

).

• Press 

 or normal volume, or 

 for high

volume.

• To change from one volume to another,

simply press the applicable START button.

• An indicator appears on the display to show

which volume level you selected.

• A series of 8 markers also appear on the

display, and then are cleared one-by-one.
The warning alarm does not sound if you
handle the clock or touch the doorknob while
these markers are on the display.

8. While markers remain on the display, close

the clock’s cover and steady the clock so that
it is not moving.

• The warning alarm is activated when the last

marker disappears from the display, and the
timekeeping display appears. Either Home
Time or Dual Time appears in the timekeeping
display, depending upon which was displayed
when you entered the Warning Alarm Mode.

Hold down the 

 button and a high-volume alarm sounds for about three

minutes. To stop the alarm, open the cover and press 

.

• You can press 

 while the clock’s cover is closed.

Volume
indicator

Start button

Markers

• The back of the unit should hang so it is about 1cm from the door’s surface.
• You cannot switch to any other mode while the warning alarm is switched on.

If you want to change to another mode, first set the selector to OFF to switch
the warning alarm off.

• Be sure always to set the sensitivity of sensor before using the warning alarm.
• If you have trouble rotating the sensitivity dial with your fingertip, use a thin,

pointed object.

• Changes in temperature can affect sensitivity, causing the Warning Alarm to

suddenly start sounding. When using the Warning Alarm on a metal door or
in environments subject to temperature drops, be sure to set the Sensitivity
dial more towards the LOW sensitivity side.

• In hot environments, the sensitivity may become somewhat weaker.
• If you do not press one of the START buttons within about 10 minutes after

adjusting the sensitivity, the clock automatically activates the warning alarm
(normal volume) and shows the timekeeping display.

• If you maintain contact with the doorknob or the hook of the clock as the last

of the 8 markers are cleared from the display (see Step 6, above), the warning
alarm will not operate until you let go of the doorknob or hook. Once you do,
the warning alarm should sound if you move the doorknob or hook again.

• After you activate the warning alarm, be sure to try moving the doorknob to

see that the warning alarm operates correctly.

• If you have set a time for an alarm, it will sound when the time is reached, even

if the warning alarm is switched on. Note that the volume of the alarm will be
the same as the volume you set for the warning alarm.

1. Press

to enter the Timekeeping Mode.

2. W h i l e   i n   t h e   T i m e k e e p i n g   M o d e ,

press

to display the Home Time.

3. Press 

 twice and the warning alarm

duration and mode indicator start to flash on
the display.

4. Use 

 and 

 to set the warning

alarm duration.

• Each press of 

 increases the duration

by one second, while 

 decreases it.

• Holding down either button changes the time

setting at high speed.

• You can set the duration within the range of

5 to 90 seconds.

5. After you finish setting the warning alarm duration, press 

 to return to the

normal display.

• If you do not operate any button for a few minutes while a selection is flashing,

the flashing stops and the clock goes back to the Normal Timekeeping display
automatically.

Mode
indicator

Warning alarm
duration

Minutes

PM indicator

Hour

Seconds

This clock lets you keep track of the current time in
two different areas: your home area and another
area.

Press

to enter the Timekeeping mode.

Press 

 to switch from Home Time to Dual Time. To switch from Dual Time

to Home Time, press

.

• The indicator 

TIME

II

 appears on the display when you select Dual Time.

1. While in the Timekeeping mode, press

to

display the Home Time.

2. Press 

 and the time starts to flash on the

display.

3. Each press of the 

 button increases the time by one minute, and

pressing 

 button decreases it by one minute.

• Holding down either button changes the time setting at high speed.
• The hour setting is changed automatically whenever a change in the minutes

increases past 59 minutes or decreases past 00 minutes.

• The seconds are reset to “00” whenever you change the minutes setting.
4. After you finish setting the time press 

 twice to return to the Normal

Display.

• If you do not operate any button for a few minutes while a selection is flashing,

the flashing stops and the clock goes back to the Normal display automatically.

1. While in the Timekeeping mode, press 

 to

display the Dual Time.

2. Press 

 and the Hour and Minutes digits start to

flash on the display.

3. Each press of the 

 button increases the time by one minute, and

pressing 

 button decreases it by one minute.

• Holding down either button changes the time setting at high speed.
• The hour setting is changed automatically whenever a change in the minutes

increases past 59 minutes or decreases past 00 minutes.

• The seconds count for Dual Time is the same as the ongoing count being

performed by the Home Time. Registering a new Dual Time setting does not
affect the seconds count.

4. After you finish setting the time press 

 to return to the Normal Display.

• If you do not operate any button for a few minutes while a selection is flashing,

the flashing stops and the clock goes back to the Normal display automatically.

While in the Timekeeing Mode, press 

  to switch between the 12-hour and

24-hour formats.
• The timekeeping format you set for one time (Home Time or Dual Time) is

automatically applied in the other time, also.