Sony HDC-F950 Manual De Usuario
Chapter 4 Adjustments and Settings for Recording
Chapter 4
Adjustments and Settings for Recording
4-19(E)
SAFETY
Set the safety marker for the selected
aspect mode.
aspect mode.
a) The DISPLAY/ASPECT switch on the viewfinder
allows you to display or not to display all markers
when MARKER is set to ON regardless of the setting
of the CENTER, SAFETY ZONE, EFFECT and
ASPECT MODE on this page.
when MARKER is set to ON regardless of the setting
of the CENTER, SAFETY ZONE, EFFECT and
ASPECT MODE on this page.
3
Perform the desired settings for each item.
1
Turn the MENU SEL knob/ENTER button to
move the arrow marker (
c) to the item you
want to set, then press the MENU SEL knob/
ENTER button.
ENTER button.
The arrow marker (
c) changes to a question
mark (?).
2
Turn the MENU SEL knob/ENTER button to
select the desired setting, then press the MENU
SEL knob/ENTER button.
SEL knob/ENTER button.
The “?” mark changes back to the arrow marker
(
(
c).
When you perform ON/OFF setting for an item,
and when value selection for that item is required,
select the value and register it in the same manner.
and when value selection for that item is required,
select the value and register it in the same manner.
4
Repeat step
3
, to make other settings as required.
5
When the menu operation is completed, set the
DISPLAY switch to ON.
DISPLAY switch to ON.
The menu display disappears from the viewfinder
screen, and the display indicating the current status of
the camera appears along the top and bottom of the
screen.
screen, and the display indicating the current status of
the camera appears along the top and bottom of the
screen.
4-6-4 Setting Gain Values for the
GAIN Switch Positions
You can set the video amplifier gains corresponding to
the L, M, and H positions of the GAIN switch. Use the
GAIN SW page of the OPERATION menu to make
these settings.
Proceed as follows:
the L, M, and H positions of the GAIN switch. Use the
GAIN SW page of the OPERATION menu to make
these settings.
Proceed as follows:
1
Set the DISPLAY switch to MENU.
<GAIN SW> 5
LOW :
c 0 dB
MIDDLE: 6 dB
HIGH : 12 dB
HIGH : 12 dB
2
Rotate the MENU SEL knob/ENTER button to
display the GAIN SW page, and push the MENU
SEL knob/ENTER button.
display the GAIN SW page, and push the MENU
SEL knob/ENTER button.
GAIN SW page
The current setting of each item appears to the
right of the item.
right of the item.
Item
Contents
LOW
Sets the gain value selected when the
GAIN switch is set to L.
GAIN switch is set to L.
MIDDLE
Sets the gain value selected when the
GAIN switch is set to M.
GAIN switch is set to M.
HIGH
Sets the gain value selected when the
GAIN switch is set to H.
GAIN switch is set to H.
3
Rotate the MENU SEL knob/ENTER button to
align the arrow marker (
align the arrow marker (
c) with the item to be
changed, and push the MENU SEL knob/ENTER
button.
button.
The arrow marker (
c) will change into a “?” mark.
4
Rotate the MENU SEL knob/ENTER button to
change the setting to the desired value, and push
the MENU SEL knob/ENTER button.
change the setting to the desired value, and push
the MENU SEL knob/ENTER button.
The “?” mark will change back to the arrow
marker (
marker (
c), and the new setting will be saved.
The gain values for L, M, and H may be set to any
of the following values: –3, 0, 3, 6,or 12 dB.
To set the gain value for another switch position,
return to step
of the following values: –3, 0, 3, 6,or 12 dB.
To set the gain value for another switch position,
return to step
3
.
5
To end menu operations, set the DISPLAY switch
to ON.
to ON.
The menu display disappears from the viewfinder
screen, and the display indicating the current status of
the camera appears along the top and bottom of the
screen.
screen, and the display indicating the current status of
the camera appears along the top and bottom of the
screen.