Sony HVR-Z1E/Z1P Manual De Usuario
Recording
44
10
Adjust the color tone.
Increasing [R] makes the selected color
reddish, and decreasing [R] makes it less
reddish (as cyan increases).
Increasing [B] makes the selected color
blueish, and decreasing [B] makes it less
blueish (as yellow increases).
No adjustment will be made at 0.
reddish, and decreasing [R] makes it less
reddish (as cyan increases).
Increasing [B] makes the selected color
blueish, and decreasing [B] makes it less
blueish (as yellow increases).
No adjustment will be made at 0.
11
Select [OK] by turning the SEL/PUSH
EXEC dial, then press the dial.
EXEC dial, then press the dial.
12
Press MENU to hide the menu screen.
To cancel the operation
Select [OFF] in step 5.
b
Note
• If the selected color range is too narrow, the color
revision may not be visible.
• In the [COLOR EXTRCT] setting, only the colors of
the effective memory are applied.
• In the [COLOR REVISN] setting, the color of the
memory that is set to be ineffective will neither be
applied nor revised.
applied nor revised.
z
Tip
• If you set both memories to the same setting, the
revision effect will be doubled.
• The Color Correction setting will be retained even if
the power is turned off. However, if you want to
revise colors influenced by time of a day, weather,
location, etc., it is recommended that you revise
them just before recording.
revise colors influenced by time of a day, weather,
location, etc., it is recommended that you revise
them just before recording.
• If you change the setting of the white balance value,
[WB SHIFT] of PICTURE PROFILE,
[SATURATION], and [PHASE], color range and
phase adjusted will change. If the above settings
have changed from when you set the Color
Correction, check the Color Correction setting
before recording.
[SATURATION], and [PHASE], color range and
phase adjusted will change. If the above settings
have changed from when you set the Color
Correction, check the Color Correction setting
before recording.
• When the white balance is adjusted automatically,
the white balance setting may vary automatically
depending on the object. To use the Color Correction
effectively, adjust the white balance manually.
depending on the object. To use the Color Correction
effectively, adjust the white balance manually.
To specify a color
A recommended way to specify a color
1
Select [COLOR EXTRCT] to change
colors to black and white, except the
target color.
You will easily recognize the selected
range.
colors to black and white, except the
target color.
You will easily recognize the selected
range.
2
Set [RANGE] to 4 or 5 to make a memory
of a single color.
of a single color.
3
Set [SATURATION] to 0 to select very
light colors.
light colors.
4
Set [PHASE] so that a color is applied to
the target object.
the target object.
5
Set [RANGE] so that the desired range of
the picture can be previewed in the
selected color.
the picture can be previewed in the
selected color.
6
If you do not need the light colored part,
set [SATURATION] so that colors are
applied only to the desired part.
set [SATURATION] so that colors are
applied only to the desired part.
7
To use the setting as a revised color,
select [OK], go back to [TYPE] and
change the setting from [COLOR
EXTRCT] to [COLOR REVISN].
select [OK], go back to [TYPE] and
change the setting from [COLOR
EXTRCT] to [COLOR REVISN].
Option
Select
PHASE
Color phase from 0 through 31.
0 (violet) - 8 (red) - 16 (yellow) - 24
(green) - 31 (blue)
In the default setting, memory 1 is set
to 19, memory 2 to 8.
0 (violet) - 8 (red) - 16 (yellow) - 24
(green) - 31 (blue)
In the default setting, memory 1 is set
to 19, memory 2 to 8.
RANGE
Range of color phase from 0 though
31.
0: No color is selected.
1: Narrow range (single color) - 31:
Wide range (The other colors of
similar color phase are also selected.)
In the default setting, memory 1 is set
to 13, memory 2 to 8.
31.
0: No color is selected.
1: Narrow range (single color) - 31:
Wide range (The other colors of
similar color phase are also selected.)
In the default setting, memory 1 is set
to 13, memory 2 to 8.
SATURA-
TION
TION
Color saturation from 0 through 31.
0: Colors from deep to light are all
selected - 31: Only deep colors are
selected.
In the default setting, memory 1 is set
to 0, memory 2 to 15.
0: Colors from deep to light are all
selected - 31: Only deep colors are
selected.
In the default setting, memory 1 is set
to 0, memory 2 to 15.