GE 106573 Manual De Usuario

Step 4: Align the flat of the shaft with the securing screw 

on the fan blade and slide the fan blade onto 
the shaft with the securing screw facing the rear 
grill.

Step 5: Center the front grill by aligning the GE Brand 

logo on the logo plate so it is upright and 
straight.  Then, holding the front grill against the 
rear grill snap each clip forward onto the front 
grill.

Final Assembly
Step 1: First, slide the inner pole up from the outer pole. 

Insert the Pole Lock Knob into the hole on the 
outer pole, to securely hold this position. Next, 
place the fan head assembly into the inner pole, 
inserting the neck of the fan into the pole open
ing. Turn the fan head’s neck until the head is 
securely locked into place. Finally, add the Tilt 
Adjustment Knob to the hole of the fan head’s 
neck. Tighten when fan head is in the desired 
position.

When using electrical appliances, basic safety pre-
cautions should always be taken including the fol-
lowing:

• Use fan only for purposes described in the 

instruction manual.

• To protect against electrical shock do not 

immerse unit, plug or cord in water or spray 
with liquids.

• Close supervision is necessary when any appli-

ance is used by or near children.

• Unplug from outlet when not in use, when mov-

ing fan from one location to another, before put
ting on or taking off parts, and before cleaning.

• Avoid contact with moving parts.
• Do not operate in the presence of explosive and 

or flammable fumes.

• Do not place fan or any parts near an open 

flame, cooking or other heating appliance.

• Do not operate any appliance with a damaged 

cord, plug, after the appliance malfunctions, or 
has been dropped / damaged in any manner.

• The use of attachments not recommended or 

sold by the appliance manufacturer may cause 
hazards.

• Do not use outdoors.
• Do not let the cord hang over the edge of a 

table, counter or come in contact with hot sur-
faces.

• To disconnect, grip plug and pull from wall out

let. Never yank on cord.

• Always use on a dry, level surface.
• Do not operate without fan grills properly in 

place.

• This product is intended for household use 

ONLY and not for commercial or industrial 
applications.

: To reduce the risk of fire or electrical

shock, DO NOT USE THIS FAN, with any SOLID
STATE Fan Speed Control Device.

Step 1: Set the fan base on a dry, level surface.

Step 2: Please make sure the On/Speed switch is in the 

"Off" position. Plug the cord into any standard 
120-volt A/C outlet.

Step 3: The SPEED is adjusted by moving the switch left
or 

right to the desired setting.

Step 4: The OSCILLATION  knob is located on 

the top of the fan motor housing. To start oscilla-
tion, push control knob down. To stop oscillation,
pull control knob up.

Tilt Adjustment
Step 1: To change the tilting angle of the fan head, sim-

ply loosen the Tilt Adjustment Knob.

Step 2: Move the fan head to the desired angle, and then 

firmly tighten the knob to lock the fan head in 
place.

Height Adjustment
Step 1: Turn the Pole Lock Knob counter clockwise to 

loosen the inner pole.

Step 2: Adjust the inner pole to the desired height, and 

firmly tighten the pole lock knob in a clockwise 
direction.

: Make sure to support the fan head

assembly when loosening the adjustable height
knob, as the weight of the fan head may cause the
inner pole to collapse.

Follow these instructions to correctly and safely care for
your GE Brand stand fan. Please remember:
• Always unplug the fan before cleaning or disassem-

bling.

• Do not allow water to drip on or into the fan motor 

housing.

• Do not use any of the following as a cleaner: gasoline, 

thinner, benzine.

(See instructions for fan head assembly)

Step 1: To access the fan blade, remove the front grill 

and then unscrew the securing screw on the fan 
blade.

Step 2: Clean the fan blade, both front and rear grills 

with a soft cloth moistened with a mild soap solu-
tion.

Step 3: Replace blade, tighten the fan blade by screwing 

the fan blade back on, and securely fasten the 
front grill.

Fan Head, Base, and Pole Cleaning
Using a soft, moist cloth, with or without a mild soap solu-
tion, carefully clean the fan base, pole, and head. Please
use caution around the motor housing area. Do not allow
the motor or other electrical components to be exposed
to water.

Base / Pole Assembly
Step 1:

Slide the bottom end of the outer pole through 

the pole ring.

Step 2:  Turn the base cover upside down and place the 

weighted insert and washer into the base cover.

Step 3:  Insert the threaded end of the L shaped locking 

lever into the hole of the washer, weighted insert 
and through the base cover.

Step 4:  While holding the base and weighted insert 

together, connect the pole to the base, sliding the
washer and L shaped locking lever into the bot-
tom of the outer pole.

Step 5:  Turn the L shaped locking lever clockwise to 

securely attach the pole to the base.

Step 6:  Set the base on the floor, weight side down. Push 

the pole ring down until it sits directly on the 
base.

Fan Head Assembly
Step 1: Position the rear grill over the motor shaft, mak-

ing certain the notches at the top and bottom of 
the rear grill fit over the prongs on the motor 
housing. Please make sure the rear grill fits 
securely against the motor housing.

Step 2: Secure the rear grill in its place using the rear 

grill mounting-ring. Turn this ring clockwise and 
tighten firmly.

Step 3: Slide the fan blade, with the hollowed interior of 

the blade facing toward the rear grill, firmly 
onto the motor shaft. The top of the motor shaft 
should lie even with the center of the fan blade.

A.) Front Grill
B.) Fan Blade
C.) Securing Screw
D.) Rear Grill Mounting-Ring
E.) Rear Grill
F.) Motor Shaft
G.) Motor Housing
H.) Tilt Adjustment Knob
I.) Inner Pole
J.) Pole Lock Knob
K.) Outer Pole
L.) Pole Ring
M.)Base
N.) Weighted Insert
O.) Washer
P.) L Shaped Locking Lever
Q.) Grill Clips (6)

A

B

C

D

E

F

Q

G

H

I

J

K

L

M

N

O

P

Your fan can be stored in the off-season either partially
disassembled or assembled. It is important to keep it in a
safe, dry location.
• If stored disassembled, we recommend using the origi-

nal (or appropriately sized) box.

• If stored assembled or partially assembled, remember 

to protect the fan head from dust.