Goodman Mfg GMVM96 Manual De Usuario
P
RoDucT
s
PeciFicATions
P
RoDucT
s
PeciFicATions
SS-GMVM96
www.goodmanmfg.com
3
s
PeciFicATions
GMVM96
0603BX
GMVM96
0805CX
GMVM96
1005DX
GMVM96
1155DX
GCVM96
0604CX
GCVM96
0805DX
GCVM96
1005DX
Heating Capacity
High Fire Input¹
High Fire Input¹
60,000
80,000
100,000
115,000
60,000
80,000
100,000
High Fire Output¹
57,600
76,800
96,000
109,250
57,600
76,800
95,000
Low-Fire Steady-State Input¹
30,000
40,000
50,000
57,500
30,000
40,000
50,000
Low-Fire Steady-State Output¹
28,800
38,400
48,000
54,625
28,800
38,400
47,500
AFUE²
96
96
96
95
96
96
95
Tons AC @ 0.5” ESP
1.5-3.0
2.0-5.0
2.0-5.0
2.0-5.0
1.5-4.0
2.0-5.0
2.0-5.0
Temperature Rise Range (°F)
20-50
35-65
35-65
35-65
20-50
20-50
25-55
Circulator Blower
Size (D x W)
Size (D x W)
10" X 8"
11" X 10"
11" X 10"
11" X 10"
10"X 10"
11" X 10"
11" X 10"
Horespower @ 1050 RPM
3/4
1
1
1
3/4
1
1
Speed
Variable
Variable
Variable
Variable
Variable
Variable
Variable
Vent Diameter³
2"
3"
3"
3"
2"
3"
3"
No. of Burners
3
4
5
5
3
4
5
Disposable Filter (in²)
576
960
960
972
641
854
854
Electrical Data
Min. Circuit Ampacity (amps)⁴
Min. Circuit Ampacity (amps)⁴
6.0
14.2
14.2
14.2
6.0
14.2
14.2
Max. Overcurrent Protection⁵
15.0
15.0
15.0
15.0
15.0
15.0
15.0
Ship Weight (lbs)
135
145
170
170
139
165
170
¹ Natural Gas BTU/h
² DOE AFUE based upon Isolated Combustion System (ICS)
³ Installer must supply one or two PVC pipes: one for combustion air (optional) and one for the flue outlet (required). Vent pipe must be either 2” or 3” in
² DOE AFUE based upon Isolated Combustion System (ICS)
³ Installer must supply one or two PVC pipes: one for combustion air (optional) and one for the flue outlet (required). Vent pipe must be either 2” or 3” in
diameter, depending upon furnace input, number of elbows, length of run and installation (1 or 2 pipes). The optional Combustion Air Pipe is dependent
on installation/code requirements and must be 2” or 3” diameter PVC.
on installation/code requirements and must be 2” or 3” diameter PVC.
⁴
Minimum Circuit Ampacity = (1.25 x Circulator Blower Amps) + ID Blower amps. Wire size should be determined in accordance with National Electrical
Codes. Extensive wire runs will require larger wire sizes.
⁵ Maximum Overcurrent Protection Device refers to maximum recommended fuse or circuit breaker size. May use fuses or HACR-type circuit breakers of
the same size as noted.
Notes
• All furnaces are manufactured for use on 115 VAC, 60 Hz, single-phase electrical supply.
• Gas Service Connection ½” FPT
• Important: Size fuses and wires properly and make electrical connections in accordance with the National Electrical Code and/or all existing local codes.
• Gas Service Connection ½” FPT
• Important: Size fuses and wires properly and make electrical connections in accordance with the National Electrical Code and/or all existing local codes.