Allstar Products Group MVP Manual De Usuario
NOTE:
The Tee
Rail/Chain Assembly is
packaged separately
from the Power Unit.
The Inner Trolley half,
Front Idler Sprocket,
Chain, and Limit Cams
are assembled on the
Tee Rail at the factory.
Follow the steps outlined below to complete assembly
prior to installation. Refer to the component
identification illustrations on the previous page.
STEP 1:
Protect the Power Unit cover from
scratching during assembly by placing it on cardboard.
Remove the two 5/16"-18 washered nuts and save
them for later use.
STEP 2:
Position the Tee Rail/Chain Assembly box
near the Power Unit. Open the box and locate the
Installation Hardware Packet.
STEP 3:
Locate the Outer Trolley half (packaged
with the Power Unit) and slide it onto the Tee Rail/
Chain Assembly with the arrow on the Trolley
Chain Assembly with the arrow on the Trolley
pointing toward the door (Front Idler).
STEP 4:
Using a 1/2" wrench, loosen the outer nut
on the Chain Tension Bracket until it is at the end of
the threaded rod. Remove and discard the small
"S" hook used to keep the chain tight during
shipping.
STEP 5:
Loop the chain around the Idler and Drive
Sprocket on top of the Power Unit and then position
the Tee Rail on the studs. Secure with the two nuts
removed in Step 1.
the Tee Rail on the studs. Secure with the two nuts
removed in Step 1.
Slightly tension the Chain by tightening the outer nut
on the Chain Tension Bracket. Remove and discard
the tape at each end of the Tee Rail Assembly. After
double-checking the Chain's alignment with the Drive
Sprocket and Front Idler Wheel, use the inner and
outer adjusting nuts on the Chain Tension Bracket to
adjust the chain to the proper tension, making sure the
chain does not twist. When correctly adjusted, the
on the Chain Tension Bracket. Remove and discard
the tape at each end of the Tee Rail Assembly. After
double-checking the Chain's alignment with the Drive
Sprocket and Front Idler Wheel, use the inner and
outer adjusting nuts on the Chain Tension Bracket to
adjust the chain to the proper tension, making sure the
chain does not twist. When correctly adjusted, the
Chain should show no droop and
be approximately 1/2" above the
base of the Tee Rail.
be approximately 1/2" above the
base of the Tee Rail.
104363
ASSEMBLY INSTRUCTIONS
104365
NOTE: If the chain is too loose or too tight, improper operation
and/or excessive sprocket noise may result.
and/or excessive sprocket noise may result.
DOOR MOUNTING
BRACKET
FRONT
IDLER
TROLLEY
OUTER
HALF
CHAIN
GUARD
WALL
MOUNTING
BRACKET
RELEASE
ROPE
AND KNOB
OPENER
HARDWARE
BAG
DRIVE
CHAIN
CHAIN
MASTER
LINKS
LINKS
TEE RAIL
RUBBER BUMPER
SUPER STATION
DELUXE WALL
PUSH BUTTON
!
Child can be pinned under automatic garage
door. Death or serious injury can result.
door. Death or serious injury can result.
• Never let child walk or run under moving door.
• Never let child use door opener controls.
• Always keep moving door in sight.
• If person is pinned, push control button or use
emergency release.
• Test door opener monthly:
Refer to your owner’s manual
Place one-inch object (or 2x4 laid flat) on floor.
If door fails to reverse on contact, adjust opener.
If opener still fails to reverse door, repair or replace opener.
WAR N I N G
PUSHBUTTON
“WARNING”
LABEL
OPENER HEAD UNIT
PHOTOSYSTEM
HARDWARE
SAFE FINISH
PHOTOSYSTEM
DOOR ARM
TUBE ASSEMBLY
TUBE ASSEMBLY
DOOR ARM ROD
RADIO
TRANSMITTER
CONTROL WIRE
SPOOL
COMPONENT IDENTIFICATION
3