Genie SILENTMAX 1000/1200 Manual De Usuario
R quired Pr ramming
Required Programming
3
MODEL AC SR3
THE GENIE COMPANY
FCC ID: B8Q AC SR3
Residential Door Operator
IC: 2 33A-CS 1D
120V. 60HZ. 5A
S/N:10XXXX XXXXXXX
STB
BWC
IWC
NOT
USED
NOT
USED
NOT
USED
NOT
USED
FROM STBs
FROM WALL
CONSOLE
STB
BWC
IWC
FROM STBs
FROM WALL
OM STB
CONSOLE
B/W
W
Open/Close Button
Opens and closes door from inside garage.
Sure-Lock™ Button
– LOCK disables controls
after door is completely
closed.
– UNLOCK allows controls to
work normally.
Indicator Light
–Red indicator light is
always ON.
–When Sure-Lock™ is ON,
the indicator light flashes.
Independent Light Control Button
Controls door opener lights from inside garage.
To powerhead
To powerhead
B/W
W
Open/Close Button
Opens and closes door from inside garage.
Sure-Lock™ Button
– LOCK disables controls after
door is completely closed.
– UNLOCK allows controls to
work normally.
Indicator Light
–Red indicator backlight is ON.
–When Sure-Lock™ is
ON, the indicator light is OFF
Independent Light Control Button
Controls door opener lights from inside garage.
To powerhead
To powerhead
WALL CONSOLE / Overview
This opener has a serial
number sticker in which
the serial numbers begin
with 10 or higher.
Wall consoles from other manufacturers may not work with openers
of these serial number groups. Use only the wall console provided with
this unit. Each wall console has three buttons.
of these serial number groups. Use only the wall console provided with
this unit. Each wall console has three buttons.
In your carton you will find one of the following
wall consoles:
Series II Wall Consoles with White Buttons
Indicator Light
Large white button will display Red when wall console is properly
wired and Sure-Lock
Large white button will display Red when wall console is properly
wired and Sure-Lock
™
is OFF. When Sure-Lock
™
is ON, this light is off
Open/Close Button
Use this button to open or close garage door. When Sure-Lock™ is
ON, the Open/Close button will CLOSE the door only.
NOTE: Constant button pressure in the CLOSE mode will override
STB fault in the powerhead and close door.
Independent Light Control Button
Use this button to turn powerhead lights ON. Powerhead lighting will
remain ON until this button is pressed again or a door action has been
completed.
NOTE: If opener has a Motion Detector sensor, it will keep powerhead
lights ON as long as motion is detected.
Sure-Lock
™
Button
When Sure-Lock
™
is ON, the powerhead cannot be activated by the
wall console or a remote.
• Press and release (or until red light goes off) to activate Sure-Lock
• Press and release (or until red light goes off) to activate Sure-Lock
™
.
• Press and release to turn Sure-Lock
™
OFF.
Series III Wall Consoles with Black Buttons
Indicator Light
Indicator light will display Red when wall console is properly wired and
Sure-Lock
Indicator light will display Red when wall console is properly wired and
Sure-Lock
™
is OFF. When Sure-Lock
™
is ON, indicator light flashes.
Open/Close Button
Use this button to open or close garage door. When Sure-Lock™ is
ON, the Open/Close button will CLOSE the door only.
NOTE: Constant button pressure in the CLOSE mode will override STB
fault in the powerhead and close door.
Independent Light Control Button
Use this button to turn powerhead lights ON. Powerhead lighting will
remain ON until this button is pressed again or a door action has been
completed.
NOTE: If opener has a Motion Detector sensor, it will keep powerhead
lights ON as long as motion is detected.
Sure-Lock
™
Button
When Sure-Lock
™
is ON, the powerhead cannot be activated by the
wall console or a remote.
• Press and hold for 5 seconds (or until Indicator Light flashes) to
activate Sure-Lock
• Press and hold for 5 seconds (or until Indicator Light flashes) to
activate Sure-Lock
™
.
• Press and release to turn Sure-Lock
™
OFF.
TIP
8
G999-393 Manual-ScrewBeltChain-EN indd 8
7/13/12 10 17 AM