Chamberlain 3575CS Manual De Usuario
21
INSTALLATION STEP 12
Connect Door Arm to Trolley
Follow instructions which apply to your door type as
illustrated below and on the following page.
illustrated below and on the following page.
SECTIONAL DOORS ONLY
•
Make sure garage door is fully closed. Pull the
emergency release handle to disconnect the outer trolley
from the inner trolley. Slide the outer trolley back (away
from the door) about 2" (5 cm) as shown in Figures 1, 2
and 3.
emergency release handle to disconnect the outer trolley
from the inner trolley. Slide the outer trolley back (away
from the door) about 2" (5 cm) as shown in Figures 1, 2
and 3.
• Figure 1:
–
Fasten straight door arm section to outer trolley with
the 5/16"x1" clevis pin. Secure the connection with a
ring fastener.
the 5/16"x1" clevis pin. Secure the connection with a
ring fastener.
–
Fasten curved section to the door bracket in the same
way, using the 5/16"x1-1/4" clevis pin.
way, using the 5/16"x1-1/4" clevis pin.
• Figure 2:
–
Bring arm sections together. Find two pairs of holes
that line up and join sections. Select holes as far apart
as possible to increase door arm rigidity.
that line up and join sections. Select holes as far apart
as possible to increase door arm rigidity.
• Figure 3, Hole alignment alternative:
–
If holes in curved arm are above holes in straight arm,
disconnect straight arm. Cut about 6" (15 cm) from the
solid end. Reconnect to trolley with cut end down as
shown.
disconnect straight arm. Cut about 6" (15 cm) from the
solid end. Reconnect to trolley with cut end down as
shown.
–
Bring arm sections together.
–
Find two pairs of holes that line up and join with bolts,
lock washers and nuts.
lock washers and nuts.
•
Pull the emergency release handle toward the opener at
a 45° angle so that the trolley release arm is horizontal.
Proceed to Adjustment Step 1, page 23. Trolley will
re-engage automatically when opener is operated.
a 45° angle so that the trolley release arm is horizontal.
Proceed to Adjustment Step 1, page 23. Trolley will
re-engage automatically when opener is operated.
Ring
Fastener
Fastener
Door
Bracket
Bracket
Clevis Pin
5/16"x1-1/4"
5/16"x1-1/4"
Curved
Door Arm
Door Arm
Straight
Door Arm
Door Arm
Clevis Pin
5/16"x1"
5/16"x1"
Inner Trolley
Outer Trolley
Lock
Washers
5/16"
Washers
5/16"
Nuts
5/16"-18
5/16"-18
Door Bracket
Bolts
5/16"-18x7/8"
5/16"-18x7/8"
Emergency
Release
Handle
Release
Handle
Lock
Washers
5/16"
Washers
5/16"
Nuts
5/16"-18
5/16"-18
Bolts
5/16"-18x7/8"
5/16"-18x7/8"
Cut This End
Figure 1
Figure 2
Figure 3
Lock Washer 5/16"
Nut 5/16"-18
Ring Fastener
Hex Bolt
5/16"-18x7/8"
5/16"-18x7/8"
Clevis Pin
5/16"x1" (Trolley)
5/16"x1" (Trolley)
Clevis Pin
5/16"x1-1/4" (Door Bracket)
5/16"x1-1/4" (Door Bracket)
HARDWARE SHOWN ACTUAL SIZE