Sunbeam SLP3300-CN Manual De Usuario

PRE-OPERATING INSTRUCTIONS
1.  Make sure the heater is OFF before plugging the heater 

into the outlet. 

2. Place the heater on a firm, level surface.
3.  Avoid overloading your circuit by not using other high 

wattage appliances in the same outlet. At 1500 Watts, 

this unit draws 12.5 Amps.

4.   Make sure unit and plug is free of moisture and debris 

before plugging into an electrical outlet.

SLP3310 (Fig. 1)
1.  Press the On/Off button   to turn unit on.
2.   Select temperature by pressing the Temperature button 

until the desired temperature is chosen.

3.   Set the Timer   for the duration in which you would 

like the heater to run.

4.   Then choose whether or not you would like to  

use the Heat & $ave™ Technology by pressing  

the Heat & $ave™ button.

Always unplug the heater before cleaning and allow to cool.
•  Lightly run a vacuum cleaner nozzle over the heater grill 

to remove any dust or dirt that may have accumulated.

•  Carefully wipe the heater with a soft, damp cloth. Please 

be very cautious near the heating elements.

•  NEVER use abrasive or flammable solvents to clean  

the heater.

•  After cleaning, be sure to completely dry the heater with 

a cloth or towel.

• Store your heater in a cool, dry dust-free location.

If your heater fails to operate or if there is no heat:
•  Do NOT attempt to repair or adjust any electrical or 

mechanical functions on this unit. Doing so will void 
the warranty. The inside of the unit contains no user 
serviceable parts. All servicing should be performed  
by qualified personnel only.

•  Make sure the power button is ON – depress   button 

or turn knob to High.

•  Check the thermostat setting; it might be set too low. 

Turn the thermostat knob clockwise until the heater 
restarts.

•  If the unit is still not producing enough heat, or  

Thermostat is set to the highest setting.

• Be patient. Give the heater time to heat up.

If your heater shuts down, follow these steps:
•  Turn Power to OFF.
• Unplug the heater and wait 30 minutes.
•  Plug in the heater, turn the power ON.
•  Your heater should now be operating properly.
•  Make sure the electrical outlet and circuit breaker  

are working.

•  You may hear a popping or crackling sound as the heater 

heats up. This is normal and safe operation. Once the 

heater heats up, the crackling sound will go away.

• Heat & $ave

TM

 automatically shuts off after 4 hours.

IMPORTANT INSTRUCTIONS
When using electrical appliances, basic safety precautions should 
always be followed to reduce the risk of fire, electric shock, and 
injury to persons, including the following:
1.   Read all instructions before using the appliance.
2.    To avoid fire or shock hazard, plug the appliance directly 

into a 120V AC electrical outlet.

3.    The heater is hot when in use. To avoid burns, DO NOT 

let bare skin touch hot surfaces. Use handle when moving 
this heater. Keep combustible materials, such as furniture, 
pillows, bedding, papers, clothes, and curtains at least 3 ft 
(0.9 m) from the front of the heater and keep them away 
from the sides and rear.

4.    DO NOT run cord under carpeting. DO NOT cover cord 

with throw rugs, runners, or the like. Arrange cord away 
from traffic area and where it will not be tripped over.

5.    This heater is not intended for use in bathrooms, laundry 

areas and similar indoor locations. NEVER locate heater 
where it may fall into a bathtub or other water container.

6.    Extreme caution is necessary when any heater is used by, 

or near children or invalids, and whenever the heater is left 
operating and unattended.

7.    Always unplug the heater when not in use.
8.   When unplugging, be sure to pull by the plug and not the 

cord.

9.   DO NOT insert or allow foreign objects to enter any 

ventilation or exhaust opening as this may cause an electric 
shock or fire, or damage the heater.

10.  DO NOT operate heater with a damaged cord or plug, or 

after the heater malfunctions, or has been damaged in any 
manner. Return appliance to manufacturer for examination, 
electrical or mechanical adjustment, or repair.

11.  A heater has hot and arcing or sparking parts inside. DO 

NOT use it in areas where gasoline, paint, or flammable 
liquids are used or stored.

12.  Use appliance only for intended household use as described 

in this manual. Any other use not recommended by the 
manufacturer may cause fire, electric shock, or injury to 
persons. The use of attachments not recommended or sold 
by the manufacturer may cause hazards.

13.  DO NOT use outdoors.
14.  To prevent a possible fire, DO NOT block air intakes or 

exhaust in any manner. DO NOT use on soft surfaces like a 
bed, where openings may become blocked.

15.  To disconnect heater, turn controls to O position, then 

remove plug from outlet.

16.  Avoid the use of an extension cord because the extension 

cord may overheat and cause a risk of fire. However, if 
you have to use an extension cord, the cord should be No. 
14AWG minimum size and rated not less than 1875 watts.

17.  If the heater will not operate, see specific instructions under 

Auto Safety Shut-off on resetting the heater.

18.  DO NOT attempt to repair or adjust any electrical or 

mechanical functions on this unit. Doing so will void your 
warranty. The inside of the unit contains no user serviceable 
parts. All servicing should be performed by qualified 
personnel only.

19.  DISCONTINUE USE IF PLUG OR OUTLET IS HOT. 

RECOMMEND OUTLET BE REPLACED IF PLUG OR 
OUTLET IS HOT TO TOUCH. 

THIS APPLIANCE HAS A POLARIZED 
PLUG (one blade is wider than the other). To 
reduce the risk of electric shock, this plug is 
intended to fit in a polarized outlet only one 
way. If the plug does not fit fully in the outlet, 
reverse the plug. If it still does not fit, contact 

a qualified electrician to install the proper outlet.
DO NOT ATTEMPT TO MODIFY THIS PLUG OR
DEFEAT THIS SAFETY FEATURE IN ANY WAY.

NOTE:
•  There may be an odor coming from the heater the first 

time you use it or after long periods of storing. This 

is normal during the break-in period. Make sure the 

heater is in a well ventilated area and continue running 

it until the smell goes away.

•  You may hear a popping or crackling sound as the heat-

er heats up. This is normal and safe operation. Once the 

heater heats up, the crackling sound will go away.

Wattage:  

1500W/ (+ 5% - 10%) 

Working Voltage:   120V AC/60 Hz 

Amperage: 

12.5A

(AVAILABLE ON MODEL SLP3310-CN ONLY)
The heater will automatically cycle between 1500 and 

750 watts. To activate the Heat & $ave™ cycle depress the 

Heat & $ave™ button. The Heat & $ave™ cycle can be 

deactivated by depressing the Heat & $ave™ button. In this 

case, the heater will run continuously at 1500 watts.

AUTO SAFETY SHUT-OFF
This heater is equipped with a patented, technologically 

advanced, safety system that automatically shuts off the 

current to the heater when a potential overheat tempera-

ture is reached. The heater can only resume operation 

when you reset it.

To Reset the Heater
If your heater shuts down, follow these steps:
1.    Turn Power to OFF.
2.   Unplug the heater and wait 30 minutes.
3.    Plug in the heater, turn the power ON.
4.    Your heater should now be operating properly.

Tip-Over Shut-Off
If the heater is knocked over, it will instantly shut off.  

To resume operation, simply place the heater in an 
upright position and turn ON the heater.

SLP3300 (Fig. 2)
1.   To turn heater On simply turn knob to desired heat 

level, 1 or 2.

2.   Select desired temperature  by turning the  

thermostat knob.

386259_SLP3300-CN_SLP3310-CN_IB.indd   2

12/8/08   11:35:50 AM