Cadet CGH402 Manual De Usuario
2
Installation Instructions
CGH402 – 20 AMP
Receptacle Configuration
Plug Configuration
CAUTION: Heater will operate on either 240 or 208 volts. Check
heater voltage and phase on label on back of heater to make sure
they are the same as the electrical service supplied. See plug
configurations below. Altering the cord in any way will void
the warranty!
heater voltage and phase on label on back of heater to make sure
they are the same as the electrical service supplied. See plug
configurations below. Altering the cord in any way will void
the warranty!
Grounding Instructions
This heater is for use on 240 (or 208) volts. The cord has a plug
as shown to the right. No adapter is available for this blade
configuration, and none should be used. The outlet type is a 240 (or
208) volt grounding outlet. When properly installed, it provides a
ground connection through the cord to the heater to protect
the operator from electrical shock.
as shown to the right. No adapter is available for this blade
configuration, and none should be used. The outlet type is a 240 (or
208) volt grounding outlet. When properly installed, it provides a
ground connection through the cord to the heater to protect
the operator from electrical shock.
MODEL
WATTS
VOLTS (60 Hz)
BTUs
AMPS
PLUG TYPE
CGH402
4000/3000
240/208
13,648/10,236
16.7/14.4
20 Amp
Specifications
Operation and Maintenance
How To Operate Your Heater
1. Turn the thermostat knob fully clockwise
1. Turn the thermostat knob fully clockwise
.
2. When the room reaches your comfort level, turn the thermostat
knob counter clockwise
until the heater shuts off. One or
two minor adjustments may be necessary as the heat becomes
better distributed throughout the area.
better distributed throughout the area.
3. To reduce the room temperature, turn the knob counter clockwise .
To increase the room temperature, turn the knob clockwise
.
Maintenance
Heaters are equipped with a permanently lubricated motor and,
therefore, no maintenance other than occasional cleaning
is required.
Heaters are equipped with a permanently lubricated motor and,
therefore, no maintenance other than occasional cleaning
is required.
WARNING WHEN CLEANING OR DISSASEMBLING HEATER,
BE SURE TO DISCONNECT HEATER CIRCUIT.
To disconnect heater, turn thermostat to “OFF”, then remove plug from
electrical outlet before cleaning or performing any maintenance.
Allow heater to cool. IMPORTANT: Heater must be unplugged
before performing any maintenance.
electrical outlet before cleaning or performing any maintenance.
Allow heater to cool. IMPORTANT: Heater must be unplugged
before performing any maintenance.
For dusting, use a soft cloth. For cleaning, use only a damp rag
and nonabrasive dish detergent. Do not use abrasive or
chemical cleaners as these may damage the finish. If heater is
used in a dusty location, use a vacuum cleaner dust brush to
remove dust and other foreign particles from the grill. Always
unplug cord and wind it around heater handles when not using.
Keep heater in a safe location for storage.
and nonabrasive dish detergent. Do not use abrasive or
chemical cleaners as these may damage the finish. If heater is
used in a dusty location, use a vacuum cleaner dust brush to
remove dust and other foreign particles from the grill. Always
unplug cord and wind it around heater handles when not using.
Keep heater in a safe location for storage.
Any other servicing should be performed by an authorized
service representative.
service representative.
Temperature Limiting Device
All heaters are equipped with a thermally actuated manual reset
limit control which automatically disconnects heating element
and motor in the event normal operating temperatures are
exceeded. If heater should fail to operate with thermostat
turned clockwise to its limit, disconnect heater and wait a few
minutes allowing heater to cool. Using a small straight object such
as a pencil, push in button located inside small hole marked
RESET. The thermal cutout almost invariably indicates a partial
or complete blockage of the air intake or exit. Be sure to keep
these areas clear in order to allow proper circulation of air.
All heaters are equipped with a thermally actuated manual reset
limit control which automatically disconnects heating element
and motor in the event normal operating temperatures are
exceeded. If heater should fail to operate with thermostat
turned clockwise to its limit, disconnect heater and wait a few
minutes allowing heater to cool. Using a small straight object such
as a pencil, push in button located inside small hole marked
RESET. The thermal cutout almost invariably indicates a partial
or complete blockage of the air intake or exit. Be sure to keep
these areas clear in order to allow proper circulation of air.
Warranty
7. IN THE EVENT CADET ELECTS TO REPLACE ANY PART OF YOUR CADET
PRODUCT, THE REPLACEMENT PARTS ARE SUBJECT TO THE SAME
WARRANTIES AS THE PRODUCT. THE INSTALLATION OF REPLACEMENT
PARTS DOES NOT MODIFY OR EXTEND THE UNDERLYING
WARRANTIES. REPLACEMENT OR REPAIR OF ANY CADET PRODUCT OR
PART DOES NOT CREATE ANY NEW WARRANTIES.
WARRANTIES AS THE PRODUCT. THE INSTALLATION OF REPLACEMENT
PARTS DOES NOT MODIFY OR EXTEND THE UNDERLYING
WARRANTIES. REPLACEMENT OR REPAIR OF ANY CADET PRODUCT OR
PART DOES NOT CREATE ANY NEW WARRANTIES.
8. These warranties give you specific legal rights, and you may also have
other rights which vary from state to state. Cadet neither assumes, nor
authorizes anyone to assume for it, any other obligation or liability in
connection with its products other than as set out herein.
authorizes anyone to assume for it, any other obligation or liability in
connection with its products other than as set out herein.
If you believe your Cadet product is defective, please, contact Cadet
Manufacturing Co. at 360-693-2505, during the warranty period, for
instructions on how to have the repair or replacement processed.
Warranty claims made after the warranty period has expired will be
denied. Products returned without authorization will be refused.
Manufacturing Co. at 360-693-2505, during the warranty period, for
instructions on how to have the repair or replacement processed.
Warranty claims made after the warranty period has expired will be
denied. Products returned without authorization will be refused.
Parts and Service
Visit http://support.cadetco.com for information on where to obtain parts
and service.
Visit http://support.cadetco.com for information on where to obtain parts
and service.
Maintenance: For more effective and safer operation and to prolong the
life of the heater, read the Owner’s Guide and follow the maintenance
instructions included with each heater. Failure to properly maintain the
heater will void any warranty and may cause the heater to function
improperly. Warranties are non transferable and apply to original
consumer only. Warranty terms are set out below.
life of the heater, read the Owner’s Guide and follow the maintenance
instructions included with each heater. Failure to properly maintain the
heater will void any warranty and may cause the heater to function
improperly. Warranties are non transferable and apply to original
consumer only. Warranty terms are set out below.
LIMITED ONE-YEAR WARRANTY: Cadet will repair or replace any Cadet
Garage/Utility Unit Heater (CGH) element or motor found to be defective
within one year after the date of purchase.
Garage/Utility Unit Heater (CGH) element or motor found to be defective
within one year after the date of purchase.
THESE WARRANTIES DO NOT APPLY:
1. Damage occurs to the product through improper installation or
1. Damage occurs to the product through improper installation or
incorrect supply voltage;
2. Damage occurs to the product through improper maintenance, misuse,
abuse, accident, or alteration;
3. The product is serviced by anyone other than Cadet;
4. If the date of manufacture of the product cannot be determined;
5. If the product is damaged during shipping through no fault of Cadet.
6. CADET’S WARRANTY IS LIMITED TO REPAIR OR REPLACEMENT AS
4. If the date of manufacture of the product cannot be determined;
5. If the product is damaged during shipping through no fault of Cadet.
6. CADET’S WARRANTY IS LIMITED TO REPAIR OR REPLACEMENT AS
SET OUT HEREIN. CADET SHALL NOT BE LIABLE FOR DAMAGES SUCH
AS PROPERTY DAMAGE OR FOR CONSEQUENTIAL DAMAGES AND/OR
INCIDENTAL EXPENSES RESULTING FROM BREACH OF THESE WRITTEN
WARRANTIES OR ANY EXPRESS OR IMPLIED WARRANTY.
AS PROPERTY DAMAGE OR FOR CONSEQUENTIAL DAMAGES AND/OR
INCIDENTAL EXPENSES RESULTING FROM BREACH OF THESE WRITTEN
WARRANTIES OR ANY EXPRESS OR IMPLIED WARRANTY.
©2009 Cadet Manufacturing Co. Printed in U.S.A. Rev. 11/10 #720100
Be sure that the electrical receptacle is of the configuration and
capacity appropriate for the heater. The heater may be used as a
heavy duty portable. It may also be hung on the wall or ceiling using
the bracket provided. The wall/ceiling mounting structure and
anchoring provisions must be of sufficient strength to support the
combined weight of the heater and mounting bracket.
capacity appropriate for the heater. The heater may be used as a
heavy duty portable. It may also be hung on the wall or ceiling using
the bracket provided. The wall/ceiling mounting structure and
anchoring provisions must be of sufficient strength to support the
combined weight of the heater and mounting bracket.